"Distributed Computing Environment / Remote Procedure Calls", is the remote procedure call system developed for the Distributed Computing Environment (DCE). This system allows programmers to write distributed software as if it were all working on the same computer, without having to worry about the underlying network code.
DCERPC inspection module is responsible for processing the data portion of the packet and performing inspection related tasks such as applying translations to IP addresses and ports contained in the packet when applicable, opening secondary channel etc., with the help of other modules
Since FWSM version 4.1 the inspectione engine has been redesigned and enhanched by RCI (Remote Create Instance) calls over RPC and the processing of RPC messaging.
Microsoft is no longer just using EPM (End Point Mapper)
As Microsoft switched from using pure RPC to use DCOM (ORPC) calls, those non-epm calls will be used more and more. Windows RPC/DCOM services use the RPC Endpoint Mapper to accept initial communications on port 135 and then dynamically transition to ports for the service.
"The OXID Resolver resides at different endpoints (ports) depending on the transport being used. The OXID Resolver optimally resides at the same endpoints as the DCE RPC Endpoint Mapper (EPM). To accommodate systems where DCOM will coexist with existing DCE RPC installations (i.e., where an EPM and presumably a complete DCE RPC runtime already exists), the DCOM implementation on that system will register its interfaces with the DCE EPM and all DCOM implementations must be able to fall back if they make DCOM -specific calls on the DCE EPM endpoint which fail."
Starting with Windows 2000, the ISystemActivator COM interface is used instead of the IRemoteActivation RPC interface.
The IOXIDResolver RPC interface (formerly known as IObjectExporter) is remotely used to reach the local object resolver (OR). The Object Resolver component is in charge to:
return protocol sequences, string bindings and machine id for an object server, given its OXID (ResolveOXID() and ResolveOXID2() (only supported by DCOM version 5.2 and above))
respond to ping requests (SimplePing() and ComplexPing() functions)
respond to ServerAlive() and ServerAlive2() functions requests
NON-EMP support for ASA/FWSM
only the RCI (Remote Create Instance) non-EPM message supported
only 1 WMI message is supported
RemoteCreateInstance (Opnum 4)
Any other message type from IRemoteSCMActivator (eg. RemoteGetClassObject) will not be passed
IOXIDResolver (Opnum 5) that is remotely used to reach the local object resolver and is part of the OXID resolver interface. This Opnum is not supported by us. Essentially, this is a RPC call from WMI (WMI uses DCOM to handle remote calls) to a non-epm subsystem that is DCOM based. Packets with opnum 5 don't need inspection support unless there is NAT involved, as there is no need for opening pinholes.
Opnum 3 & 4, EPM.
Opnum=5, this does not contain port numbers and FWSM does not inspect this. If there is a NAT involved, FWSM does not inspect.
CSCsk97762 - ENH: Allow DCERPC inspect to open pin-holes for WMI queries. non epm map
CSCto43960 - FWSM: DCERPC inspection of packet with multiple segments fail
Hello Experts @Rob Ingram @balaji.bandi I currently got AnyConnect VPN setup which is mapped through DNS to our Public Domain and its working fine. I want to setup another AnyConnect VPN which will be mapped through DNS to ...
Hello, Sorry in advance if this is not the correct thread to post in. We are currently migrating over to Auvik from Solarwinds NCM and running into a bit of an issue. We have one AD account that is being used as CLI creds for all of our switches...
Hello everyone;I am doing a deployment to create a new tacacs server through cisco ISE (authenticating to an AD).The thing is that I am not receiving any TACACS log on the Cisco ISE, and on the firewall, I can observe that the requests from the test SW ar...
@Arne Bier Hi, i have the blocking issue. My Pixel with Android-11 is not able to get authentication from Cisco setup on WiFi enterprise. I did create the domain name as "motorola.com" in cisco server. I also extract out the CA cert(CAcert.crt) ...
I require to remove AAA configuration and put back again after complete my activity,Can you please guide me, what would be the best way to remove it. My worries is, when I remove beow command at any point of time, Will it throw an error "command authorzat...