Activity in Service Providers
Resolved! A9K-36x10GE-TR last ISO XR supported firmware
Hello,I am trying to find the last supported IOS XR firmware for ASR 9010's line card A9K-36x10GE-TR.Does anybody have information about this case?I have A9K-RSP880-TR
Accedian AMN-1000-TE
Now that Cisco has acquired Accedian network I can seem to find a manual for a AMN-1000-TE device. Anyone know where to find one of these?
BFD over IPv4 implementation on NCS5500 platform
Before going further ...This document describes BFD over IPv4 implementation on NCS5500 platform. BFD over IPv6 implementation is not discussed in the current article, but you can find complete info here: https://community.cisco.com/t5/service-prov...
'asr9k-ether-ea' detected the 'warning' condition 'TCAM allocation fai
why this alarms came
In A9K-4HG-FLEX-SE Simultaneously usable port Combinations
Hi, In A9K-4HG-FLEX-SE , There are 24 number of 10G ports(12 and 12) and 16 number of 10G/25G ports (8 and and 4 number of 100G ports (2 and 2) What are the port combinations that can be used? For example, if we use 12 x 10G port in one plane, can't...
A9K-MOD200-TR to A9K-MOD200-SE
Hi, Is there any possibility to upgrade A9K-MOD200-TR card to A9K-MOD200-SE without any hardware changes? Best Regards, Madura
CPE
Hi,I have a customer CPE on private AS 65520 which has EBGP session to a MPLS PE device.I want to strip/hide the private AS so it uses the public AS of my PE.On the neighbor facing the CPE i have used the remove-private-as command and as-override ho...
PBR config in Cisco NCS540 IOS XR
I was using IOS XE and moved to NCS540L IOSXR. OS Version 7.7.21I used policy-map to achieve my PBR requirement for multiple default-route in IOS XE. In XE there is no such option to achive the PBR according to my needs. There I also found ABF (ACL B...
BFD Support on IP Unnumbered Interfaces? - ASR 9000
I wanted to make a post to inquire about support for BFD using IP Unnumbered interfaces on the ASR 9000 platform. I was conducting some tests in my lab using BFD with IP Unnumbered between an ASR 920 and an ASR 9010 router with OSPF as my IGP. When ...
CFM - Unable to get remote maintenance points learning
Greetings,I am trying to establish CFM connectivity using emulation (CSR1000v).I am running VPLS (Manual discovery) for end to end connectivity.The topology in use is CE4 - PE2 - PE3 - CE6Connectivity in place , what am not able to get the remote mai...
Remote fault and SIGLOSS on NCS2K-400G-XP-LC
Hello,I'm facing this issue with a connection between two NCS2k-400G-XP-LC cards.Site A has Remote fault on port 8-1 and Site B has SIGLOSS on port 8-1. Both ports have QSFP-100G-SR4-S plug-in to them. I tried to replace the MPO cables, the cards the...
extended community
Hi All,I'm trying to attach an extended community to a specific subnet learned from a CPE using the below confighowever i don't see this community attachedip prefix-list TEST_BGP_IN permit 192.168.1.0/24route-map TEST_ROUTE_POLICY permit 5match ip ad...
I want to monitor traffic by multicast group.
hello.I am using NCS5508 version 7.3.2.I want to monitor real-time traffic by multicast group with NMS.Multicast traffic is shown in show mfib route rate, but the checked OID shows a value of 0.The OID was checked from CISCO-IETF-IPMROUTE-MIB in Cisc...
EVPN/VXLAN-Multi Site Layer 2 issue
Dear all,I am running in to very strange problem - currently busy with preparation in our LAB for a migration of EVPN/VXLAN setup from single-site to multi-site. During the testing in our LAB I have discovered the following.The LAB is already in mult...
ASR 920 EVPN device tracking
Starting with ios-xe 17.5 on ASR920, when configuring a EVPN bridge domain, device tracking functionality is automatically enabled and corresponding evpn policies block some ARP requests.Looking for a way to disable device tracking functionality on ...
| User | Helpful Count |
|---|---|
| 4 | |
| 3 | |
| 2 | |
| 2 | |
| 1 |
