Small Business Voice and Conferencing

Multiple incoming calls in a SPA514G

Good morning everyone,I have a problem and I'm not sure how to solve it. I try to explain.I have a UC540 with severals SPA514G and everything works fine. Now we have added a sip trunk in the UC540 and it also works well but the problemis as follows, ...

Call directly a blast group or a extension, what is the difference?

Hello, I have a UC540 with severals SPA phones.I just enable a SIP trunk with 6 channels.My phone has four lines and each line support up to 2 calls, then my phone could receive up to 6 calls at maximun.In my incoming dial plan , I setup a blast gro...

UC320 DTMF Tones

Good Afternoon,Just looking for a bit of advice. I don't really have any experience in this area, but I've been asked to look into it anyway.We have a Cisco UC320 phone system. We are trying to use a dial-in voice-conferencing system that relies on i...

IP phone SPA504G blank screen

Hallo,I've uploaded, with TFTP, an updated italian dictionary (from cisco) for my SPA504G but the phone after reading and rebooting shows an empty blank screen, without life.I've tried:cisco firmware reset, but the phone doesnt bring up the network i...

enable auto reboot

Is there an option anywhere in the SPA series of phones to force a reboot every X number of days?

Unable to select the call inputs in Analogue phone during a call via SPA112

I'm not entirely sure which location/selection this should be in, please move if neciscary.I have been having some trouble for some time with using my phone connected to my modem via the SPA112. Whenever I call a place that has an automated message t...

UC520 Caller-ID problem

HeyWe have a UC520 via analogue line.Now we want to switch to a SIP trunk and this works.Incoming and outgoing calls arrive, only when we call out does the number come through as an anonymous to the recipient.He seems to be calling out the number of ...

how many wireless mics are possible on 8831 conf phone?

on a conference phone base model 8831, how many additional "Wireless" mics can be added if any?Note we already have 2 wired mics connected.

SPA232D bridge with problems in vLans

Hi!I am a Cisco SPA232D configured in bridge mode (...I already have a Cisco RV325 that does me the vLans routing work and it interfaces with my ISP's modem).The SPA232D is configured in vLan class 11 (...my native vLan is in class 1). I have a "big"...

Cisco SPA502G provisioning

Hi guys,I have a cisco SPA502G IP Phone, i have configured a new name under voice register global and also issued the 'create profile' command, but still if you call the extension it displays the old name.Kindly assist.Am using cme vesrion 8.6

SPA525G

Will SPA525G work with Spectrum IP Phone Network?

connecting two ip phones

For the experts on this forum this might be a too easy question: I would like two connect two cisco spa 301 ip phones with one cisco sg300 switch between both. Just to be able to make phone calls from one ip phone to the other, nothing else. Which si...

SPA514G One Touch Park with Asterisk 13

I use Cisco SPA series phones and I utilize one touch button to park calls and the operator announces the parking lot number the call is parked on before the call is hung up.On the Cisco at least on Asterisk 11 this requires: Keep Referee When REFER ...

Help with weird noise in SPA 303 - 7.5.5

Hi,a customer has 4 SPA 303 - 7.5.5 all the same. In one there is this little noise/pitch like an interference, only in one of the four, the other three are4 OK. I included a mp3 file (in spanish) to hear the sound.Any idea, I would really appreciate...

Is it possible to completely factory reset a Cisco 514G that has a customisation?

I have about 10 Cisco 514G deskphones from my old provider and I've tried playing around with them however, I've noticed that they are locked down. I tried a factory reset but when I log in through the web interface I can see that under customisatio...

Small Business Voice and Conferencing

Forum Posts

Multiple incoming calls in a SPA514G

Call directly a blast group or a extension, what is the difference?

UC320 DTMF Tones

IP phone SPA504G blank screen

enable auto reboot

Unable to select the call inputs in Analogue phone during a call via SPA112

UC520 Caller-ID problem

how many wireless mics are possible on 8831 conf phone?

SPA232D bridge with problems in vLans

Cisco SPA502G provisioning

SPA525G

connecting two ip phones

SPA514G One Touch Park with Asterisk 13

Help with weird noise in SPA 303 - 7.5.5

Is it possible to completely factory reset a Cisco 514G that has a customisation?

Get ready! Great things are coming to Cisco Community

New name, same great product: Cisco Spaces

Congratulations to the July 2022 Spotlight Award winners!

Route a call from a user to group instead of VM (UC560)

Shared Line Configuration Issue

Cisco SPA504G set up to be used as Land line telephone

UC560 License Migration

Using speed dial on SPA112