Hello, I have implemented SDA in two sites with Fabric in a Box of two switches in a stack in each remote site. Everything is working fine without any problem. But now in one of the sites I have to add a stack of two more switches placed in another f...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
Hi,Can you please tell me about all specifications of fusion router and also please clarify that this fusion router is a non poe device?
Hi I have two Border nodes Anyware and two fusion routers i configure EBGP bentween two borders (Anywhere) and two fusion i configure iBGP between the two border (Anywhere) B1-->Fusion1 : EBGP B2-->Fusion2 : EBGP B1-->B2 : iBGP when i loss the con...
According to the SDA design guide:Reduce subnets and simplify DHCP management—In the overlay, IP subnets can be stretched across the fabric without flooding issues that can happen on large Layer 2 networks. Use fewer subnets and DHCP scopes for simp...
Resolved! L2Flooding setup
Hello, When enabling L2Flooding, Underlay ASM must be configured either via LAN Automation or manually. Whatever the method used, MSDP and a Loopback60000 used as Anycast-RP should be configured on redundant Border nodes. This is documented in variou...
When adding a IP pool to a VN i want to give the VLAN a name. When i do this with the API it is not accepted and the name is auto-generated as if i do not give an name to the VLAN.The schema defenition of the api gives the required vlanName key which...
I've been searching to see if these devices have a monitoring API if they're not managed by DNA Center. Anyone know? Thanks https://www.cisco.com/c/en/us/products/collateral/wireless/catalyst-9100ax-access-points/datasheet-c78-741988.html
Resolved! Loopback Interface Registration in LISP
Loopback registration in LISPHi All,I have fabric campus configured with only problem policy enforcement in inter-VN traffic. This is not working because traffic goes out of VXLAN and SGTs are lost. I want to configure my Edge switches so that they w...
Resolved! Layer 2 Border node ethernet map-cache
Hi!We have deployed a stacked 9500 as our layer 2 border node, configured with lan-automation and have an issue with migrating wired clients.We have a solution where clients authenticate with MAB over ISE and can migrate their wired connection to oth...
Guysnoticed "amber" output on one of FIABs. Any idea on how to drill down to root cause on that single "MAC registration inconsistency" pls? FIAB1#show lisp site summary----------- IPv4 ----------- ----------- IPv6 ----------- ----------- MAC -------...
Since I am new to SDAccess fabric world just putting up a weird question. Is there by any means we can run a SDA fabric in a layer 2 setup (by configuring the different IP pool subnet's gateway in a L3 switch or firewall outside the fabric).
Cisco DNA Center Version 2.3.3.7-72328 We have a use case where we'd like to swap a C9500-24Y4C for a C9500-48Y4C. Is this possible in DNAC, or would the new 48 port switch need to be added to the inventory/fabric site, assigned the fabric role[s] be...
How to migrate from 2 nodes co-located CP/BN on an SDA site to 2 dedicated CPs and 2 dedicated BNs? For instance, following the SDA CVD if I start with a small site model for a given site/fabric with CP/BN co-located, how can I later migrate to a med...
Hello,I'm going to do my best to describe this so bear with me. We have an existing SDA campus deployment... roughly 6 large "facilities" as independent fabrics that connect to a central site via IP Transit (BGP). That central site is the distributio...
Hi, We are about to implement sd-access, does anyone have a guide to configuring fiab and how it should be incorporated into the sd wan solution...Thanks in advance Ciro Gustavo Mele
