Switches - Small Business

I have a SG300 that is running 1.4.5.02 and need some help with ACL's. My intention is to lock things down where services aren't accessible from the outside. Here is the configuration at the moment. We've tested and SSH and HTTPS are accessible from ...

Hi, I am pretty new to networking with Cisco equipment, but we have had an RV325 now for a while that I've gotten used to and have a couple VLANs set up on. We had been running with just the RV325 and a WAP371 supporting about 35 associated devices a...

I have 9 PCs at a SG300-10 switch running. Everything works fine, however, in the RAM memory log I can see permanently DOWNs and UPs. What is the reason for that behaviour? Another swtich SG300-20 does not show this behaviour.214748332717/12/12 10:10...

http://www.cisco.com/c/en/us/products/switches/350-series-managed-switches/literature.html Why there is no documentation?  No Maintain and Operate Guides, no Reference Guides, ...

Hello, I was hoping someone could help with a potentially easy (stupid) question.  I have powered up the switch and the system light is blinking green.  Now I want to and want to add it to an existing network.  According to the quick start guide, whe...

I am very rusty with commands but i was curious with these 3 sg500 setup in a stack. For some reason when i run the sh run command it does not show me any ports past 1/1/36 but if i do a show interface description it shows me all the interfaces for a...

We have 2(two) SG300-28 switches. We have several VLANS that need to be truked between switch A and switch B 1. We are able to create 1 TRUNK port  that includs vlan 2,3,4 and it works fine between switch A and B.  We are now trying to create a 2nd T...

Hello!  I have 5 of SG500X-24 PORT GIGABIT WITH 4-PORT 10-GIGABIT STACKABLE MANAGED SWITCH that i have recently started managing.  Recently, those switches have been acting up and makes our drive go down with internet connection for some of our users...

Hi guys, So here's the setup: 2 switches: Switch1 3560x Switch2 3560x (10gbe c3kx-nm-10g module) 3 vlans: 1(default) 200 (storage) 201 (vmotion) poweredge servers: a blade m1000e chassis with 10gbe pass through module esxi for ose on the blades. ...

Anyone have an opinion on this?Setup:An sg300-10 configured in L3 mode.There are 4 vlans defined (with 4 IPv4 addresses, though the sg300 is not routing -- other device does).In IPv4 all works fine.Trying to add IPv6 to my network I found out that:- ...

I have a couple of SG300 28 port switches that I just purchased over the last few months, we changed out our phone system so we using voice over IP phones and the phones are now connected to our pc's.  For some reason, the ports are dropping on the s...

I have a cisco sg500-52 port running in a stack config with another cisco sg500. I cannot get console access into the box. i have tried turning off the secondary switch and trying to console into the master. i have tried multiple different baud rates...

I've forgotten username & password of SG300-28 28-Port Gigabit Managed Switch. Is there any to recover them? but I don't want to lose configurations. 

I'm using a SG300-28MP switch (firmware updated to the latest version): and when I make a connection to an Axis M3014 POE ip camera, nothing happens. The camera doesn't boot up and it seems it doesn't get any power through POE. When I use the camer...

Hi All, I have a sg 300 running multiple VLans. One Vlan, 223 is for BACNet BMS, 3 ports are assigned to this VLan, 1 for the BMS Admin, 1 for connection to the rest of the BMS Lan and 1 for a Crestron Processor, which interogates the BACNet and feed...