Switches - Small Business

Hi All, I've am not that advance level user of Cisco WLC but I have recently deployed (Dynamic VLAN) wired network security with cisco switches. The same I need to configure with Cisco WLC 2504 using the existing VLANs created in my network.  Scenar...

Hi Team, I have Cisco SG300-52 52 Port Managed Switch. Does the switch support Inter-VLAN Routing with the help of a Layer 3 Device? If yes, please help me with the configuration. Regards, Sri Charan M S

Hi,I have upgraded my SG200-08 switches from firmware version 1.0.5.1 to version 1.0.6.2. Since that new firmware is active, the network-printing from my Macbooks and iMacs is not working anymore. They all have TCP/IP connected network printers (not ...

Hello, We have 3 switchs SG500-52 and i would know what is the maximum speed we can have for stacking mode. PS : Enclosed the actual configuration of our stack. Is this the optimal speed ? Thank you for your answers. David ROSSI

Hola¡ Estoy configurando un SG500 y no consigo que los equipos de las diferentes subredes hagan ping al router, por lo tanto no tienen internet. Pego la configuracion a ver si me podeis echar una mano, muchas gracias¡¡¡¡¡ config-file-headerSG500v1...

I just bought a new SGE2000P switch.  In trying to do the configuration for use, I have logged in using the serial interface, set the IPV4 information and saved it.  I then try to connect using the web interface.  I get the welcome screen, login in u...

Hello, I'm looking for IOS version ce500-lanbase-mz.122-25.FY of the Catalyst Express 500 but this model is not listed on the download categories for switches on Cisco.com. Once, maybe one year ago, i downloaded from there this IOS version but unfor...

We have several SFP-300 series PoE switches already configured and in production usage.What is the appropriate procedure to export the configuration from one of these switches, then import into a newly-purchased switch of the same model??The only thi...

Have a question regarding the configuration of an SMB SG500-28P switch which we set up to be stacked with 4 other switches (all are SMB SG50028P). We preconfigured the switch before going and installing at the customer's site. When onsite we found it...

Hello, I would like to reboot a SG300 switch via snmp but I'm not able to. Here is my setup: 1 SG300 switch: 10.1.0.105 - Firmware Version (Active Image): 1.4.0.88 1 snmp management device: 10.1.0.9 - linux snmp is enabled on the switch  created a c...

Hey, I've got a question regarding this particular switch. I am trying to get part of my network configured and the only thing I have left is this switch. On it I have multiple VLANs but for the sake of simplicity and my problem, I have our user sub...

Goodday everyone, I have Small Business SG200-50 Cisco Switch for our business, the download speed of the internet is 100mb and the upload speed is 15mb, I would like to limit the bandwidth 10mb download and 1mb upload per device, but i am new to C...

Hi, I am getting an error in Cisco 2960 and HP ProCurve 2920 Switches I am having an issue with Printers only to directly go to VLAN1 as I can't setup for authentication, below is the port configuration. Everything is working fine as of my need exce...

For some reason this is just eluding me.  Using WAP371s attached to SG300 PoE swtiches we find that they become unstable after a few days in some situations (in others they never get flaky, it's very strange) and would like to use the Time Range opti...

Hello all, I have an Sg500X that I am configuring. I am having a problem configuring te1/1/1. I can pull it up through a console session. I get the conf-if I add switchport mode trunk. Then exit and sh run-config and there is no interface listed for...