Switches - Small Business - Page 371

Looking for support docs and videos? Check here

We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...

Helpful support links - Updated September 2023 w/ Catalyst 1200 - 1300

(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...

Resolved! SG-300 LAG speed

Dear forumers,I'm configuring two SG-300 switches at the moment, and I'm trying to connect them with two cables.I've set up the LAG like this (on both switches): LAG001.jpg And a got the following result: LAG002.jpg This means my connection is at onl...

SRW224G4 V1.1

Hello,We have small network with 15 Computers all connected to SRW224G4 . After a power brake our switch dosent "boot" anymore. I see all leds working flashing etc but no network acces, no Serial acces. When i try connecting to serial port and "rese...

SLM 2024 VLAN Config help

I'm new to managed networking. So I'm having trouble understanding how to set up my switches properly. I have a closed network with about 20 switches and 2 IDF's. No router, and no internet. I have a SLM 2024 in want to have 4 ports set up with a...

SF 200E-24P not upgrading firmware

Help!I have just received a Cisco SF 200E-24P switch and need to upgrade the firmware. The current version is 1.0.0.12 an need to load the latest (or at least 1.1) to get CDP etc. However when I use the upgrade option in the switch I get an error of....

How to prevent a loop with an unmanaged conference room switch

We have multiple conference rooms that have unmanaged 8-port switches that connect to a single port in the room. Is there a configuration we can set on that port that will prevent looping from occuring. We've had numerous times that someone has conne...

Resolved! SG300-28 - Firmware 1.2.7.76 with DVA: How to use Guest VLAN ? (Bugs00131469)

Hallo,can you please explain me this problem more in detail, please:##################################################################Problem: When a DVA authorized port tries to re-authenticate and RADIUSattributes no longer include VLAN attributes,...

Resolved! What steps are needed to untag default vlan to gigabit port on SRW208P

We have VLAN 1 disabled on our standard Cisco Catalyst switches and use VLAN 11 as our default. We have recently added VLAN 221 for voice while implementing a new Cisco UC system. I can't seem to disable VLAN1, however, I have made the default VLAN...

SG300 Simple GVRP

Hello, I have 2 SG300 switches and all I want is to propagate VLAN info from one to other. I do not have computers with GVRP compliant NICs, so I dont want that auto registeration functionality on access ports. I want VLAN prop via trunks and swi...

Resolved! Bandwidth limited through SF302-08P switch?

Just put in an SF302-08P switch with two AP541N's. Just a Comcast modem connects into the switch along with the two WAPs, nothing else. Speedtest through the cable modem with nothing plugged into it is 48Mbps. Then connecting a single laptop via the ...

Cisco SG300-10 IP Based ACL limit source IP

HiI'm administrator of small network. I wish to replace my old switches by new SG300-10 and SG300-16 managed switches. I have big trouble in my network becouce everyone can assign IP his neighbour (or any IP) to his network card. I have policy that I...

sg300 and routing

I'am testing a sg300 switch in layer 3 mode and created different vlansvlan1: 172.16.0.0/16vlan4: 192.168.4.0/24I inserted a default route to our internet router (172.16.0.55) and there a route back to the switch 172.16.2.101I defined no acls at the ...

SG200-26 How to configure fast NFS filetransfer

I have a SG 200-26. Port 1 goes to Internet. Port 2 to a Synology NAS. Port 3 to a 'small' gigabit hub with a computer and a media player connected. All gigabit connections. The media player uses NFS to access a share on the NAS. How do I configure t...

How many watts do the Cisco SGE2010P 48 POE switches draw?

Resolved! How enable 802.1x with 'Wake on LAN' cisco sge 2010 ?

Hello,We have acquired a cisco sge 2010 to replace our distribution switch. I set up the 802.1X network. Everything works great except I can not find how to enable 802.1x with 'Wake on LAN' on this kind of switch. Do you have an idea?On catalyst I sa...

New User Working To Implement VLANs Correctly.

Hey group, looking for your input on what I am attempting to implement on the the Cisco equipment we have purchased for a small shop. I know the value of implementing VLANs to seperate network traffic and confine traffic to it so I am trying to expan...

Switches - Small Business

Forum Posts