Hi all Multicast is not transported when a device with multiple multicast stream is connected to the switch.As soon as we switch to a single stream it is working. We have 7 single stream video controllers (C10 Optelecom-nkf) that are working fine.2 v...
Forum Posts
Resolved! 9300 switch, showing prompt switch:
Hi all,I have a 9300 switch, after boot stuck in rommon mode prompt switch:How can I make the switch to boot in normal mode, please advisei also try boot from USB, its showing me below outputswitch: Dir usbflash0:Size Attributes Name- - - - - - - - -...
Dear community memebers,I need to test a scenario containing cisco nexus 9300 switches on a virtual lab. I tried to configure vpc on my switches both in eve and gns3. But I have a problem. I configured my switches, and the vpc is formed fine and is u...
Dear all, Can we install the C3KX-PWR-440WDC or PWR-C1-715WDC inside the WS-C3850-12S and do they function together?I see that the 3750X can use some or most of the C1 power supplies from the 3850 switch:C3KX-PWR-440WDC & PWR-C1-440WDCAnd I see that ...
I have a Cisco 4500X, and it has an IOS image (cat4500e-universalk9.SPA.03.08.01.E.152-4.E1.bin). I tried to upgrade to the latest version with the K9 feature, but the upgrade process failed. Then, I tried upgrading the iOS (cat4500e-universal.SPA.03...
I recently ran into an issue at one of our remote sites where a switch won't recognize the installed fiber module. One of the ports on that module is the uplink. We suspect that the module is faulty but until we are able to get back on-site, we are r...
"I set up a switch, but I want to be able to access it; however, I can't access it via Telnet or HTTPS.I believe the problem is that I did not set up the username. Is there any way to access it remotely?I am attaching the main setup.enable secret 9 $...
Dear community,I have a LACP Portchannel configured on a Catalyst connected to a Nexus vPC.When I shutdown one Port of the vPC the connected port on the catalyst goes into lacp suspended state.That´s expected, as the port doesnt receiev any lacp pdus...
Hi, I am a beginner in using the Cisco Packet Tracer & I am having trouble trying to exclude the above. Any guidance or help would be appreciated.Thank you
Hey folks,I've been refreshing my home LAN and my home lab (I work for an NDR vendor) and I'm looking to get some 10Gbe functionality internally. Specifically my Proxmox server and my Unraid server both have 10Gbe addon NICs which are currently just ...
Hello people, I am configuring a dynamic route using OSPF for the topology in the zip file. I have done it, but Router 3, 4, 5, and 6 can't seem to be able to ping Router 1's Eth1/0. Is this normal for OSPF configuration? Or did I do something wrong?...
Hi, I want to enable jumbo frames bettwen nexus 9300 and cat3850.nexus is on NXOS: version 9.3(8)cat is on IOS XE Software, Version 16.09.05On nexus side I have set sh int po1interface port-channel1description MTU9kswitchport access vlan 555mtu 9216v...
Hi,My c3745 printed "No password set" when I tried to get to the enable mode. So, I tried to do password-recovery, but it is always in the user-mode mode despite the attempts to type "Cntrl-Break", "Alt-b", "Cntrl-C" during the initial reload.It fail...
I inherited two Nexus 5548 switches with fabric extenders and I'm looking for the proper way to remove port channel group and the associated interfaces which are connected to a server we are repurposing and does need the four connections for ethercha...
Hello Community:I seem to have myself up a river of effluence without a means of locomotion and am hoping someone can give me some help so I can get unstuck. I've got a Cisco 4500-X switch running IOS-SE v3.11.04E and I've encountered problems with...
