we configure a password policy, but we can't link it to the local user with a secret, if we need to link it with a local user, we should use password instead of a secret, any help hereThanks
Forum Posts
Resolved! C9300 and C9500 how many VRFs supported?
Hi all, I can not find in data sheets or FAQs how many VRFs are supported in C9500 or C9300. Does someone know where can I find this info?
I have a pair of SX350X switches which are stacked and running our core network.Is it possible to do a firmware upgrade on these without any downtime?
Resolved! 3650 High Memory Used
A warning log of "%PLATFORM-3-ELEMENT_CRITICAL:Switch 1 R0/0: smand: 1/RP/0: Used Memory value 98% exceeds critical level 95%" appears. show processes memory This is the suspicious process. 3650#show processes memory Processor Pool Total: 8856...
Resolved! Problem with N9K since upgrade
Hi everyone,We have 2 N9K C93180LC-EX with 5 N2K-C2348 FEX attached (dual home).We experienced some issues during the upgrade as we are getting some ports in "inactive" status. We tried to understand where the problems is but we can't figure it out. ...
HiJust want to confirm the 3850 series switch model End of switch maintenance date.There is publication on the link below, but there's no date of switch maintenance, does it mean Cisco have not release yest?End-of-Sale and End-of-Life Announcement fo...
Hi, I have a cisco 3550 switch which I power cycled but now its stuck at Press RETURN to get started! ==============================================Base ethernet MAC Address: 00:XX:XX:XX:XX:XXXmodem file system is available.The password-recovery mech...
Hi, I'm trying to prefer R2 route for the multicast traffic (without using static mroute) from R1 (receiver) to R4 (source):Receiver (R1): 10.10.10.10Source~(R4): 10.0.45.5I'm completely new to multicast and still trying to understand how it works b...
Hi Team, am using 2x9300 catalyst switches and i have configure two interface from server with two different VLAN 148, 14 and between two switches I have port Chanel with trunk . am getting this error on both switches , thanks in advance for your as...
Resolved! Command rejected: Bad VLAN allowed list. You have to include all default vlans, e.g. 1-2,1002-1005.
Hi guys,Im trying to simulate a switch in Gns3 and i use 16ESW module in a cisco 3700 router.Can you please tell why im getting this record after i try to filter which vlans pass through my trunk port:Router(config-if)#switchport trunk allowed vlan 2...
Resolved! v-mismatch on H/W catalyst 9300
Hello everybodyI have a problem for stack switches that can't connect, the problem is v-mismatchnoted that the ios version is the same, but my question is:the system boot version is different, is that the problem cause? and how to solve also, the H/W...
Resolved! Catalyst 9200 trunk promiscuous
I have two stacked 9200 and i want to configure a private vlan trunk in promiscuous mode but i can not find how. Is this feature available on this model at all?
HelloI don't know if this is the right forum, but i recently switched to Windows 11 and ever since i have been having issues with transferring a file from a switch to my computer via TFTP, for example a config backup using the command "copy start tft...
Hello All, I have a question, I built the following DHCP pool and ACL on the Cisco core. When the ACL is on the computer doesn't able to get IP address from DHCP but when I turn off the ACL it works perfectly fine. So here is the question when comput...
Hello! I was wondering if I could get advice/input when it comes to QoS at the distribution layer of a network topology. Here's a high-level of our network topology.Soon to deploy two Cisco C9500k in a Stackwise HA configuration. It will have about 1...
