Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! is the sg300-10sfp working at 10Gbits?

Dear all,I'm searching for a switch able to cope with 10Gbit/s transfer rates (for a small, personal, cluster built from multiple workstations).Recently, I found this switch on sale: sg300-10sfp. I'm not sure it only works at 1Gbit/s or at 10Gbit/s.....

WS-C6509-E: WS-CAC-6000W FAILURE

Hi all, I want to confirm the PSU of the chassis WS-C6509-E is faulty or not. So my question is, by look at the system alarm, its confirmed that the PSU is failed: - environmental alarms: system minor alarm on power-supply 1 power-output-fail (raised...

Hafiz_HR by • Level 1
  • 570 Views
  • 2 replies
  • 0 Helpful votes

Stackable Cisco 9606

There are two 9606. Each has 2 Supervisor Engine 1.Is it possible to configure the cluster in between so that all four Supervisor Engine 1 are involved?If so, how do you do it? thanks

Trum by • Level 1
  • 471 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Cat9k hostname always changed to Switch every reload

INFOC9200L-24T-4GSystem Bootstrap, Version 17.5.1r [FC4] PROBLEMS:-every time reloaded the hostname changed to Switch from original hostname CAT9K STEPS TAKEN:https://www.cisco.com/c/en/us/support/docs/switches/catalyst-9300-series-switches/216850-co...

nawir by • Level 1
  • 1519 Views
  • 5 replies
  • 0 Helpful votes

Stratix 5700 duplicated MAC address after NAT

Hi, I have a Stratix 5700 with a public IP 10.50.71.YYY, I have setup the NAT to translate a local IP 192.168.1.XXX to a public IP 10.50.71.XXX, when I ping the switch Public IP and the NATed device Public IP from a direct connection from my laptop t...

hsaul17 by • Level 1
  • 525 Views
  • 1 replies
  • 0 Helpful votes

Object-group Access control list

Hi there, I need to implement ACL in router using object group method. The scenario is host(1.1.1.1) send images to 3 servers ( 2.2.2.2,3.3.3.3, 4.4.4.4) via tcp port 3320,104,2104 and the host retrieve data from the server via same port.Appreciate y...

newbie_08 by • Level 1
  • 324 Views
  • 0 replies
  • 0 Helpful votes

Resolved! * means valid route in bgp.what is valid?

Hi everybody"* " means Valid in BGP . What does BGP consider before declaring a route as valid?For example, below, R1 is receiving an update about 6.0.0.0/8 from its ibgp peer.  The next hop is 196.196.196.1 is not reachable by R1 but yet R1 still co...

sarahr202 by • Level 5
  • 3321 Views
  • 5 replies
  • 0 Helpful votes

VPLS and Spanning Tree

Hello All! Greetings! 1. We have 3 switches installed in different geological locations and are interconnected via SDH network.  applications used on these switches fall under the same subnet and very well communicating via SDH Network since everythi...

Resolved! cat2960などのVLAN表示とトランク、アクセス各ポートの一括表示の仕方

お世話になっております。Cat2960などのL2SWにおいてトランクポートとVLANメンバシップの一括表示（このトランクにはVLANなになにが通過許可）とか、アクセスポートでVLANメンバシップの一括表示（int Gi1/0/1はVLANなになにでアクセスポートで活性化済みとか、、）、とか、VLANメンバシップでトランクポートかアクセスポートが一発でわかるコマンドとかないでしょうか？　よろしくお願いいたします。 

View All
Review Cisco Networking for a $25 gift card