08-09-2016 12:03 PM - edited 03-08-2019 06:56 AM
Hi Team,
I'm getting the following error when i try to enter the following command into et3/2 interface on a KN7 any help will be appreciate thank you.
sh run int po105
interface port-channel105
description 10.197 (SS105005)
switchport
switchport mode trunk
switchport access vlan 10
switchport trunk native vlan 10
N7K1(config)# int et3/2
N7K1(config-if)#
N7K1(config-if)# switchport trunk native vlan 10
N7K1(config-if)# switchport mode trunk
N7K1(config-if)# channel-group 105 mode active
command failed: port not compatible [port access VLAN]
** You can use force option to override the port's parameters
** (e.g. "channel-group X force")
** Use "show port-channel compatibility-parameters" to get more information on failure
08-09-2016 12:24 PM
Hi,
Try this:
no interface port-channel105
exit
int et3/2
channel-group 105 mode active
exit
interface port-channel105
switchport
switchport mode trunk
switchport trunk native vlan 10
no sh
and test again.
HTH
08-09-2016 12:30 PM
By doing this it will be deleting the inteface port-channel 105 then it will create the channel again is that correct.
08-09-2016 01:51 PM
Yes, that is correct. From that point forward you just add any config line to the Portchannel and the physical interface will inherit it.
HTH
08-09-2016 01:35 PM
Hi!
This error appears when you try to bundle two interfaces which has no identical configuration. Please be sure that all links you are trying to bundle into your port-channel 105 have the same configuration.
Have a nice day, best regards!
JC
09-16-2022 04:15 AM
You have a port-channel interface configured like this:
interface port-channel2
description --- port-channel ---
switchport
switchport mode trunk
switchport trunk allowed vlan 101
Member interfaces must have the same configuration before entering the port channel.
If not, here's what happens.
ITESYS_nexus7400# sh run int eth4/3
interface Ethernet4/3
description --- port 1A ---
no shutdown
ITESYS_nexus7400# conf t
Enter configuration commands, one per line. End with CNTL/Z.
ITESYS_nexus7400(config)# int ethernet 4/3
ITESYS_nexus7400(config-if)# channel-group 2
command failed: port not compatible [switching port]
** You can use force option to override the port's parameters
** (e.g. "channel-group X force")
** Use "show port-channel compatibility-parameters" to get more information on failure
The switch basically tells you that it can do this job for you if you use the force option.
So I try again.
ITESYS_nexus7400# conf t
Enter configuration commands, one per line. End with CNTL/Z.
ITESYS_nexus7400(config)# int ethernet 4/3
ITESYS_nexus7400(config-if)# channel-group 2 force
No error reports now. But the interface will automatically be configured with the parameters of the port-channel interface:
ITESYS_nexus7400# sh run int ethernet 4/3
interface Ethernet4/3
description --- port 1A ---
switchport
switchport mode trunk
switchport trunk allowed vlan 101
channel-group 2
no shutdown
09-16-2022 04:56 AM
switchport mode trunk <- this make port trunk
switchport access vlan 10 <- then you add this command which overrride the above one and make port access port
hence the PO not work because it see now port as access not trunk
09-22-2022 07:50 PM
port channel vs port physical need same mode access or trunking
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide