cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
913
Views
0
Helpful
10
Replies

N7K-M108X2-12L module reloaded by itself- Service "ipfib" hap-reset

sakkaveelp1
Level 1
Level 1

Hello Guy, 

I found module 9 (N7K-M108X2-12L) on N7K has reload by itself, please help for investigate the reason it reloads?

2023 Feb 14 20:56:19 N7010 %SYSMGR-SLOT9-2-SERVICE_CRASHED: Service "ipfib" (PID 19480) hasn't caught signal 9 (no core).
2023 Feb 14 20:56:20 N7010 %MODULE-2-MOD_DIAG_FAIL: Module 9 (Serial number: JAF1521xxxx) reported failure 9/1-9/0due to Service on linecard had a hap-reset in device DEV_SYSMGR (device error 0x17a)
2023 Feb 14 20:56:27 N7010 %ETHPORT-5-IF_DOWN_MODULE_REMOVED: Interface Ethernet9/5 (description:X00487-TLR13100:xxx9070036:xxx;TAQ04/01;Core179,180:10G{TA3TMxxxxx}) is down (module removed)
2023 Feb 14 20:56:27 N7010 %BGP-5-ADJCHANGE: bgp-7470 [29202] (default) neighbor 58.97.121.xx Down - other configuration change
2023 Feb 14 20:56:38 N7010 %PLATFORM-2-MOD_DETECT: Module 9 detected (Serial number JAF1521xxxx) Module-Type 10 Gbps Ethernet XL Module Model N7K-M108X2-12L
2023 Feb 14 20:56:38 N7010 %PLATFORM-2-MOD_PWRUP: Module 9 powered up (Serial number JAF1521xxxx)
2023 Feb 14 20:56:38 N7010 %PLATFORM-5-MOD_STATUS: Module 9 current-status is MOD_STATUS_POWERED_UP
2023 Feb 14 20:57:35 N7010 %BIOS_DAEMON-SLOT9-5-BIOS_DAEMON_LC_PRI_BOOT: System booted from Primary BIOS Flash
2023 Feb 14 20:58:50 N7010 %VDC_MGR-5-VDC_STATE_CHANGE: vdc 1 state changed to updating
2023 Feb 14 20:58:50 N7010 %VDC_MGR-5-VDC_STATE_CHANGE: vdc 1 state changed to active
2023 Feb 14 20:59:03 N7010 ipqosmgr: System queuing policies already exist, no need to recreate the policies
2023 Feb 14 20:59:08 N7010 %MODULE-5-MOD_OK: Module 9 is online (Serial number: JAF1521xxxx)
2023 Feb 14 20:59:08 N7010 %SYSMGR-SLOT9-5-MODULE_ONLINE: System Manager has received notification of local module becoming online.
2023 Feb 14 20:59:08 N7010 %PLATFORM-5-MOD_STATUS: Module 9 current-status is MOD_STATUS_ONLINE/OK
2023 Feb 14 20:59:10 N7010 %ETHPORT-5-SPEED: Interface Ethernet9/5, operational speed changed to 10 Gbps
2023 Feb 14 20:59:10 N7010 %ETHPORT-5-IF_DUPLEX: Interface Ethernet9/5, operational duplex mode changed to Full
2023 Feb 14 20:59:21 N7010-TT2-MBA-1 %BGP-5-ADJCHANGE: bgp-7470 [29202] (default) neighbor 58.97.121.xx Up

 

N7010# sh module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 6 10/40 Gbps Ethernet Module N7K-M206FQ-23L ok
2 6 10/40 Gbps Ethernet Module N7K-M206FQ-23L ok
3 2 10/40/100 Gbps Ethernet Module N7K-M202CF-22L ok
4 24 10 Gbps Ethernet Module N7K-M224XP-23L ok
5 0 Supervisor Module-2 N7K-SUP2 active *
6 0 Supervisor Module-2 N7K-SUP2 ha-standby
7 24 10 Gbps Ethernet Module N7K-M224XP-23L ok
8 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok
9 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok


nxos version 7.3(2)D1(1)

-------------------------------------

I'm not sure with device has error or hitting any bug ID?

Thank you. 

 

10 Replies 10

If I am right you had issue with NSK memory now the N7K is reload
are you using N3K as access and N7K as Core/Agg SW ??

if yes share the topology 

@MHM Cisco World 

This is the switch (N7K) I don't have an issue with memory, Now everything is working fine after the reload. 

what I meaning that are these two NSK connect to each other ??

This N7K is a mobile device network and sorry I don't  have the topology

Please inform me in the bug use line card F3-Series while my device uses M1-Series, it can look like the same line card? 

and I notic it doesn't have workaround for the bug

Thank for your help full

 

F3 is different than M1-sereis. 
let me more check 

Thank you so much for taking the time to help.

@MHM Cisco World  After found log in this bug, line card was reloaded by supervisor or not?

https://www.cisco.com/c/en/us/support/docs/interfaces-modules/nexus-7000-m1-series-32-port-10-gigabit-ethernet-module/116227-technote-m132xp-00.html

this link to check M1 card in N7K 

NOTE:- please please keep notice that show tech is heavy in CPU. use it carefully.
NOTE:- check how you use show tech before apply this command  

Review Cisco Networking for a $25 gift card