What version has this issue ?

Nicholas Poole · ‎06-22-2010

I am trying to connect a Cat3560G switch to an N7K pair via a vPC. The VLANs I wish to trunk are being suspended, I am getting the following error messages:

2010 Jun 22 17:03:36 N7K-Core1 %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 2,301 on Interface port-channel2 are being suspended. (Reason: Vlan is not allowed on Peer-link)

The VLANs do exist , but a STP instance isnt created for it (I am using RPVST);

N7K-Core1# sh vlan id 2

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------

2 VLAN0002 active Po2, Po75

N7K-Core1# sh spanning-tree vlan 2

ERROR: Spanning tree instance(s) for vlan does not exist.

Port Vlans Err-disabled on Trunk

--------------------------------------------------------------------------------

Eth1/9 none

Eth1/10 none

Eth1/17 2,301

Eth1/18 2,301

Eth1/25 2,301

Eth1/26 2,301

Eth2/2 none

Eth10/1 none

Eth10/2 2,301

Po2 2,301

Po75 2,301

Po99 none

The VLANs are allowed on the trunk (it by default allows all)

interface port-channel1

description * vPC Peer-Link *

vpc peer-link

spanning-tree port type network

I have turned off bridge assurance as a test but no no avail.

Any ideas?

Ganesh Hariharan · ‎06-22-2010

Hi,

Allow the vlan 2 and 301 over the trunk using the below command

Nk-1(config-if)# switchport trunk allowed vlan 2,301

http://conft.com/en/US/prod/collateral/switches/ps9441/ps9670/configuration_guide_c07-543563.html

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

Nicholas Poole · ‎06-22-2010

it trunks all vlans by default

Nicholas Poole · ‎06-22-2010

my bad, spotted the obvious mistake

Muhammed AKYUZ · ‎06-22-2010

Can you send the po2 config on Nexus?

cperkins2 · ‎08-13-2010

I'm having the same issue between a pair of vPC'd 5020s going to a 6500 using a vPC.

All VLANs which are supposed to go over the trunk/vPC, are showing as err-disable on trunk. I've checked all configs and they are the same... allowed vlans match on all po interfaces and physical interfaces.

6509:

interface Port-channel78

description Connection to n5020s @ in the MDC

switchport

switchport trunk encapsulation dot1q

switchport trunk native vlan 2240

switchport trunk allowed vlan 2002-2006,2010,2014,2018,2022,2024,2026,2240

switchport trunk allowed vlan add 2244,2248,2252,2254,4050,4052,4054

switchport mode trunk

end

N5020-1:

interface port-channel100

description Uplink to dist01 @ A building

switchport mode trunk

switchport trunk native vlan 2240

switchport trunk allowed vlan 2002-2006,2010,2014,2018,2022,2024

switchport trunk allowed vlan add 2026,2240,2244,2248,2252,2254,4050

switchport trunk allowed vlan add 4052,4054

vpc 100

N5020-2:

interface port-channel100

description Uplink to dist01 @ A building

switchport mode trunk

switchport trunk native vlan 2240

switchport trunk allowed vlan 2002-2006,2010,2014,2018,2022,2024

switchport trunk allowed vlan add 2026,2240,2244,2248,2252,2254,4050

switchport trunk allowed vlan add 4052,4054

vpc 100

All member ports reflect the correct config.

Both 5020s have the same config for the peer-link:

interface port-channel2

description VPC Peer-link

vpc peer-link

spanning-tree port type network

Output form 'show interface trunk"

n5020-1# sh int tru

--------------------------------------------------------------------------------

Port Native Status Port

Vlan Channel

--------------------------------------------------------------------------------

Eth1/1 2240 trnk-bndl Po100

Eth1/2 1 trnk-bndl Po200

Eth1/17 2240 trnk-bndl Po78

Eth1/18 2240 trnk-bndl Po78

Eth1/19 2240 trnk-bndl Po87

Eth1/20 2240 trnk-bndl Po87

Po78 2240 trunking --

Po87 2240 trunking --

Po100 2240 trunking --

Po200 1 trunking --

--------------------------------------------------------------------------------

Port Vlans Allowed on Trunk

--------------------------------------------------------------------------------

Eth1/1 2002-2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2254,4

050,4052,4054

Eth1/2 180-183

Eth1/17 180-183

Eth1/18 180-183

Eth1/19 2002-2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2254,4

050,4052,4054

Eth1/20 2002-2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2254,4

050,4052,4054

Po78 180-183

Po87 2002-2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2254,4

050,4052,4054

Po100 2002-2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2254,4

050,4052,4054

Po200 180-183

--------------------------------------------------------------------------------

Port Vlans Err-disabled on Trunk

--------------------------------------------------------------------------------

Eth1/1 2002-2004,2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2

254,4050,4052,4054

Eth1/2 180-183

Eth1/17 180-183

Eth1/18 180-183

Eth1/19 2002-2004,2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2

254,4050,4052,4054

Eth1/20 2002-2004,2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2

254,4050,4052,4054

Po78 180-183

Po87 2002-2004,2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2

254,4050,4052,4054

Po100 2002-2004,2006,2010,2014,2018,2022,2024,2026,2240,2244,2248,2252,2

254,4050,4052,4054

Po200 180-183

--------------------------------------------------------------------------------

Port STP Forwarding

--------------------------------------------------------------------------------

Eth1/1 none

Eth1/2 none

Eth1/17 none

Eth1/18 none

Eth1/19 none

Eth1/20 none

Po78 none

Po87 none

Po100 none

Po200 none

Thank you,

Chris Perkins

INX Inc.

Nicholas Poole · ‎08-13-2010

You did what I did, omitted the trunk command on the vPC peer-link. Your config is:

interface port-channel2

description VPC Peer-link

vpc peer-link

spanning-tree port type network

...so add:

switchport mode trunk

cperkins2 · ‎08-13-2010

Hi - thanks for the quick reply!

I also noticed that running the command "switchport trunk allowed vlan all" told the peer-link to allow all vlans. I didn't see it doing that by default... ?

Also, I changed the port-type to "normal" for the spanning-tree config. I had an issue with one of the downstream devices wanting to be STP root for some VLANs... I changed the peer-links to "spanning-tree port type normal" and that solved the problem of the 5010 wanting to be root instead of our 6509 upstream.

Thanks,

Chris

Radium Fu · ‎08-21-2012

Answer

interface port-channel1

description * vPC Peer-Link *

vpc peer-link

spanning-tree port type network

You do need one more command. to turn peer link as trunk. otherwise it will not transfer any vlan through Peer-link

"switchport mode trunk"

Jarvin Christian Palma · ‎01-30-2013

Hi,

I got the same issue but the difference is the configuration is in fabricpath.

interface port-channel1

switchport

switchport mode fabricpath

spanning-tree port type network

vpc peer-link

%ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 971 on Interface port-channel1 are being suspended. (Reason: Vlan is not allowed on Peer-link)

Vinod Kumar · ‎01-13-2015

We have some issues with creating new vlans on the N7K switches. This is due to a bug (CSCtr08143) on the current software version we are running.

The permanent fix is to upgrade the switches to new version as we are running a really old code but there is a simple workaround that resolves the issue if you see it..

Here is the workaround:

-Create vlan on both switches

-Confirm that both switches have vlan created by using command ‘show vlan’ or ‘show vlan id xxxx’

-Perform a ‘no spanning-tree vlan xxxx’

-Then perform ‘spanning-tree vlan xxxx’

-Use ‘show spanning-tree vlan xxxx’ to see if the vlan has now been created and if forwarding

Cheers!!

Vinod

Vinod Kumar · ‎01-13-2015

We have some issues with creating new vlans on the N7K switches. This is due to a bug (CSCtr08143) on the current software version we are running.

The permanent fix is to upgrade the switches to new version as we are running a really old code but there is a simple workaround that resolves the issue if you see it..

Here is the workaround:

-Create vlan on both switches

-Confirm that both switches have vlan created by using command ‘show vlan’ or ‘show vlan id xxxx’

-Perform a ‘no spanning-tree vlan xxxx’

-Then perform ‘spanning-tree vlan xxxx’

-Use ‘show spanning-tree vlan xxxx’ to see if the vlan has now been created and if forwarding

Cheers!!

Vinod

msmith508 · ‎04-04-2016

NEVER disable spanning tree on a production switch!

You will create a loop!

If you create a loop you may need to reboot the switch in order to recover from it!

vikasmandhan · ‎05-17-2016

What version has this issue ? I'm having the same issue while creating a new VLAN. it's showing suspend.

Jarvin Christian Palma · ‎03-02-2015

Just want to ask if you have included the "peer-switch" configuration under vpc? I think both vPC Peers should have the same STP priority (per vlan) on both N7K1 and N7K2. Please see attached power point file. Hope this will help.

Cheers,

Jarvin

Nexus 7000 vPC suspended VLAN problem