Tag: "catalyst_5000" in "Networking Knowledge Base"

Buy or Renew

Latest Tagged

Port status is errdisable due to BPDU guard - ( ‎06-22-2009 04:02 PM )

by on

0 Comments 223748 Views

0 Comments

223748 Views

Catalyst switches that run CatOS generate the %SYS-3-P2_ERROR: 1/Have run out of vbufs (internal buf... - ( ‎06-22-2009 04:04 PM )

by on

0 Comments 645 Views

0 Comments

645 Views

The %MGMT-4-OUTOFNVRAM: Out of NVRAM space: error error message is seen on Cisco Catalyst switches r... - ( ‎06-22-2009 04:04 PM )

by on

0 Comments 943 Views

0 Comments

943 Views

The Error Msg: mfree 2: m= [Hex] , m_type=0 PID = 0 Kernel an error message appears in the logs of a... - ( ‎06-22-2009 04:06 PM )

by on

0 Comments 837 Views

0 Comments

837 Views

How to enable and disable the Finger service or protocol in Cisco switches - ( ‎06-22-2009 04:07 PM )

by on Latest post on by

2 Comments 26225 Views

2 Comments

26225 Views

How to configure the Gigabit Ethernet fiber-optic interface to support duplex speed in Cisco Catalys... - ( ‎06-22-2009 04:11 PM )

by on

0 Comments 10595 Views

0 Comments

10595 Views

Recovering from ErrDisabled port due to misconfiguration - ( ‎06-22-2009 04:39 PM )

by on Latest post on by

2 Comments 246315 Views

2 Comments

246315 Views

Catalyst switch running CatOS getting the error message %SPANTREE-7-MSGAGEEXPIRY: Msg Age timer expi... - ( ‎06-22-2009 04:41 PM )

by on

0 Comments 1892 Views

0 Comments

1892 Views

The %SYS-3-PORT_ERR: Port mod_num/port_num swBusCRCErrorDrop messages are logged on a Catalyst 500... - ( ‎06-17-2009 10:21 PM )

by on

0 Comments 870 Views

0 Comments

870 Views

Supervisor Engine module does not come online due to continuous booting loop, invalid boot variable,... - ( ‎06-22-2009 04:45 PM )

by on

0 Comments 1865 Views

0 Comments

1865 Views

Top Tagged

How to reset the VLAN and VTP information back to factory defaults in Cisco Catalyst switches - ( ‎06-22-2009 06:09 PM )

by on

0 Comments 34747 Views

0 Comments

34747 Views

The "%SYS-5-SYS_TIMECHNG: System time has changed to due to summertime" error message is received in... - ( ‎06-22-2009 06:09 PM )

by on

0 Comments 1565 Views

0 Comments

1565 Views

How to disable STP on a per port basis in Cisco Catalyst switches - ( ‎06-22-2009 06:08 PM )

by on

0 Comments 160177 Views

0 Comments

160177 Views

Slow performance of LAN due to a high degree of multicast traffic or frequent disruption of multicas... - ( ‎06-22-2009 05:40 PM )

by on

0 Comments 15627 Views

0 Comments

15627 Views

Configure ISL trunking between Catalyst switches that run CatOS and Cisco IOS (native mode) - ( ‎06-22-2009 03:40 PM )

by on

0 Comments 1469 Views

0 Comments

1469 Views

A SPAN destination port is shown as "not connected" and does not communicate with the rest of the ne... - ( ‎06-22-2009 05:35 PM )

by on

0 Comments 8486 Views

0 Comments

8486 Views

Fan LED on Catalyst 4000, 5000 or 6000 series modular chassis is not green due to a hardware problem - ( ‎06-22-2009 03:40 PM )

by on

0 Comments 530 Views

0 Comments

530 Views

The "port is a non-802.1q port" error message is displayed on Cisco Catalyst switches that run CatOS - ( ‎06-22-2009 05:34 PM )

by on

0 Comments 1228 Views

0 Comments

1228 Views

How to configure a default gateway on the Catalyst 6500, 6000, 5500, or 5000 series running CatOS so... - ( ‎06-22-2009 03:38 PM )

by on

0 Comments 9846 Views

0 Comments

9846 Views

Card in a modular Catalyst 4000, 5000 or 6000 series chassis does not function properly or is not on... - ( ‎06-22-2009 05:33 PM )

by on

0 Comments 2603 Views

0 Comments

2603 Views

Top Taggers

User

Count