Activity in Technology and Support
STP functionality after stack broken Cisco C9300 Stack
Hi, Here I have attached a snap for your reference.A and B are C9500X switches and C and D are C9300X switches. C and D are a switch stack. I need to know in case of stack broken between C and D what happen to STP ?This is a SDA environment and A an...
Help with OPENDNS Linux IP UPDATER
Hi,I've been using OPENDNS and Linux IP UPDATER without issue until recently (AFAIK). I changed my password a few weeks ago and last week I realized the IP address wasn't changing. In troubleshooting, I realized I neglected to also change my password...
8200L password recovery function
Hi,Can I do the 8200L password recovery even if no service password recovery is configured ?I tried to send break many times when booting but there is not working.Thanks!
New data centers coming to Denver and Dallas
We are excited to announce the expansion of Cisco Secure Access with the addition of two new data centers. These data centers will start accepting traffic in early June, 2026.New Data Center Locations:Denver, Colorado, USADallas, Texas, USAThese are ...
Meraki dashboard with C9300L-48P-4X switches
Let me explain what is happening and the issue we are facing.Our setup is quite simple, as shown above. We have a stack of seven Cisco C9300L-48P-4X switches converted to Meraki Dashboard mode. All switches are currently running IOS XE 17.15.5. Since...
Wireless dot1x order
For wired connection we can set authentication order to dot1x mab for example, can we do same thing in the wireless? So the wireless client will try connect using dot1x first and use mab if authentication failed.
SD-WAN VMANAGE CLUSTERING
Hello All, am trying to deploy vmanage (version-20.18.2.1 )cluster using EVE-NG with the following configuration. Am using single interface under vpn0 but still getting Status as PENDING as mentioned below. Secondly can we use vpn512 for clustering p...
Severe Audio/Video Latency in Cisco Jabber 15.2.260904 After Upgrade
We are investigating potential latency issues in Cisco Jabber (15.2.2.60904), specifically related to audio and video calls. Since the version update, our users have reported a latency of 5, 10, or even 20 seconds for video and audio (out of sync), r...
Resolved! Default Admin password on MPP Phone
I would like to use the built in PCAP feature on an 8865 phone running MPP firmware.To do this on the phone's built in web server, you have to login to the web gui with the Admin account. But I cannot find the default password or a place in Control ...
Resolved! Cisco Catalyst C9500 not supporting 1G SFP
Hello,i am trying to conncet SFP-1G-SX on C9500-24Y4C-A but ports are going to error-disable each time i try. i connected on different switch also but same issue. i am getting below error. Switch Log: Transcceiver-3-Not_Supported: C1/0: imod: detec...
A new Recommended Release MX Security & SD-WAN firmware is now available
A new Recommended Release MX Security & SD-WAN firmware version is available. Firmware MX 19.2.8 was released on 2026-05-21 and has been in this firmware category since 2026-05-21 UTC.
API Module - Versioning Confusion
I'm a bit confused by the API Module Versioning...2026 - Meraki Portal What's New & Changelog - Cisco Meraki Developer HubThis site shows Version 1.70.0 as the May 2026 release. This site has always been my go-to for figuring out what API calls are ...
Problem with AP: CSCwk71043 - Assoc Resp failed
CSCwk71043 - Assoc Resp failed due to CLIENT_DEL_DRIVER_ADDING_ENTRY_IN_FIRMWARE_FAILEDThe problem is becoming more and more frequent. Is there already a possible permanent solution/update? Symptom: Assoc Resp failed due to CLIENT_DEL_DRIVER_ADDING_E...
ASA Firewall VPN
I have a question: I’ve set up the Cisco Duo Authentication Proxy with RADIUS for MFA push on both the server and the firewall. Do I also need to create a Network Policy and Access Service on the server so the firewall can authenticate properly?
Enabling & Troubleshooting Endpoint Agents on RoomOS Devices
Introduction & PrerequisitesQuick Review: Enabling ThousandEyes Agents on Cisco RoomOS DevicesTroubleshooting: When the Agent Doesn't Show Up on the ThousandEyes PortalStep 1: Verify Configuration in Webex Control HubStep 2: Check Device Settings in ...
| User | Helpful Count |
|---|---|
| 81 | |
| 61 | |
| 58 | |
| 49 | |
| 44 |
