Activity in Technology and Support
Port down après établissement up/up et avec présence du signal
Bonjour,J'ai deux CE cisco C6500 version software 15.2 SY4 connectées aux boucles transmissions, j'ai pas de visibilité sur la partie WDM, mais le port Gi/3 sur CE 2 et le port Gi1/2 sur CE 1 tombe down après une période de fonctionnement, et réstaur...
How to Trigger Route Pattern based on the Calling Party Number in CUCM
Is it possible to trigger a route pattern based on the calling Party number?For example, MYApp with Caller ID "544449" having a SIP trunk with Cisco calls a Cisco extension 3000 (Not DN).My requirement is to transform this caller ID 544449 to 44449 b...
Call Forwarding
I am using 10.1.7.20 Unified Communications Self Portal to forward calls to my AT&T iPhone cell phone, but the calls are not being connected. Is there anything I can do on my end to enable this connection?
Cisco IOS XR Software, Version 7.0.1 Netconf
Established Netconf connection using ssh, Received Hello Message from device along with capabilities.I sent below Hello message<?xml version="1.1" encoding="UTF-8"?><hello xmlns="urn:ietf:params:xml:ns:netconf:base:1.0"><capabilities><capability>urn:...
CCMP help -Create user to add agents only
UCCEDearsI am in situation where we have CCMP 12.6 , i am very new to this platform and task assigned to me is to add user which can only add agents and skills.Kindly if someone have experience and can share the details steps.I have already done bel...
Resolved! Cisco Secure Firewall ISA3000 ip on interface
Hello, So i recently got a Cisco Secure Firewall ISA3000 and i was trying to set it up, however, i noticed that my interface commands are different. mobile(config-if)# int Gi1/1mobile(config-if)# ip address 10.10.1.37 255.255.255.0^ERROR: % Invalid i...
Firmware for RV130W not available?? What gives?
https://www.cisco.com/c/en/us/support/routers/small-business-rv-series-routers/series.html#~tab-downloads No listing for the RV130W can I get some help here?
9300x connect management interface on front panel port on itself
In our dr datacenter we have 2x9300x.we would like to use the gi0/0 management interface but having no other switches we need to connect it to a front panel port on itself.is this kind of scenario supported?
OSPF Multiple Areas Configuration
Hi, My name is Quan. I am new to OSPF and dynamic routing.I've been learning about RIPv2 configurations and OSPF configurations.While i am doing in this OSPF Multiple Areas lab I had a problem regarding the routing table doesn't show results as I tho...
Newbee Need help with understanding UCCX Script logic
I'm trying to understand what condition triggers a False condition in this ScriptI'm trying to test this Script and make sure callers have the option to go to voicemailI've tried taking a call and staying on the line, then I called 4 more times fro...
Troubleshooting CAPWAP and DHCP Issues in Cisco 9800-CL Wireless Lab
Hi everyone,I'm currently working on a practical WiFi lab. The goal is to broadcast SSIDs mapped to two different VLANs: VLAN 20 and VLAN 30. I'm using the Cisco 9800-CL Wireless LAN Controller (WLC) deployed as a VM on VMware Workstation running on ...
Private-Vlan with VRRP
Hello to everyone.I am working on this topology for 2 months but i wasnt able to find the accurate solution even i asked from prefessional but their solution wasnt accurate.My qustion is ----> How i can activate Private-vlan while using SVI with VRRP...
Resolved! 2960X Upgrade Path from 15.2(2)E6 to 152-7.E12
Hi All! Is there a cisco document that confirms if there is direct upgrade from 2960X Upgrade Path from 15.2(2)E6 to 152-7E12?
C1300 Bridge Multicast Filtering not enabled
I purchased a C1300 for my home office lab explicitly so I could manage the multicast traffic effectively, and avoid flooding my LAN.It clams to have IGMP Querier/Snooping and filtering, but when I come to enable this, it says that Bridge Multicast F...
virtual catalyst 9800 stuck on boot
hi.. we've been having this issue for a while now, every time we try to deploy and OVA for a catalyst it works for a while then get stuck on this stage , no matter what version, those are the only vm's that are affected by this, we've tried on multi...
