TelePresence and Video Infrastructure

Resolved! ISDN phone on Vic2-2Bri-NT/TE card

I installed a Vic2-2Bri-NT/TE on our 2851 with CME, when I attach an ISDN phone directly on Vic2-2Bri port I always get busy tone as soon as I pick up the phone. In the log I read :ISDN BR0/1/0 Q931: TX -> DISCONNECT pd = 8 callref 0x84Cause i = 0x82...

cisco services for migrated tandberg units

hi,would like to inquire regarding Cisco services for migrated TANDBERG units using the following scenarios:a. if the migrated TANDBERG unit was still enrolled using V26 and got faulty; do we need to shipped it back for repair, or Cisco will consider...

Resolved! Custom privileges for user, MSE 8510 blade

Hi!Does anyone know if it is possible to create a user account on the MSE 8510 blade with more "custom" privileges than the pre-configured settings?Example: Can you create a user that may view one or more conferences ( and only those) and have "limit...

external audio calls from VCS through CUCM?

I have a Tandberg VCS system I was able to get integrated with CUCM through a SIP trunk and can make OnNet audio calls between video endpoints and IP phones, however, I can't figure out how to make external calls from the video endpoints. It seems t...

3241 ISDN GW backup D-channel using NFAS

Hello,We have 4 ISDN PRI's from ATT provisioned as a trunk group with 1 primary D-channel and 1 backup D-channel. In the Codian gateway under the port configuration, it only gives the option of Primary or None for D-Channel type. How can we designa...

Nortel Unistim

Hi All, we have an issue were the first few seconds of a phone call there is no sound and after a few seconds you can hear the other end and can talk fine from then on, this seems to be a very issolated issue and only happening to a few phones and in...

Resolved! Cisco VCS and IP Address Dialing

I have a question about Ip address dialing and the VCS. In the admin guide it says that the VCS considers an IP address to be known if it either:- is the IP address of a locally registered endpoint- falls within the IP address range of one of the sub...

Resolved! MeetMe time limit

We have a MeetMe call setup for a group that needs to do a con-call but no one will be at the office to initiate it. So they asked us to setup a MeetMe before 16 hours before the con-call is suppose to happen. We tried this before but the conferenc...

Resolved! Unable to make outgoing calls on Tandberg E20

Dear All,Will be gratefull if someone could help us in getting a solution.We have Tandberg E20 registered (as third-party device advanced) to CUCM 7.0. We are able to make calls to E20 from any SIP or SCCP Phones. But we are unable to make calls from...

Resolved! 2 Office VOIP design, and PVDM usage

Dear colleagues, i have 2 , A and B sites, with same spec's "number of users 16 with IP phones, and just VOIP needed , both will connected via Internet using a FW then IPsec to other branches",for VOIP solution A:will call PSTN via 4 analog lines, so...

Cisco Unified Video advantage

Ok... first time here, so please be patient. thanksI have a Cisco 2851 (Software Ver 12.4) and all works perfectly for voice calls... then on nice day...my outgoing calls stopped working... nothing...works fine internally...but external calls would ...

Number displaying

Hi Can anybody tell me if it is possible to configure a Codian ISDN gateway (3500 Series) so that it displays its direct call ID on outgoing calls. I want the endpoints to display the H.323-ID on outgoing IP calls and there DID (ISDN) numbers on outg...

CUCM 7.1 sip to Tandberg MXP 3000

Hi All,Does anybody have any pointers on getting a CUCM 7.1 cluster talking to a Tandberg MXP 3000 via SIP.We have separate ISDN Bri for our Tandberg and want to get rid of them and pass voice only calls via call manager and a 2821 gateway router wit...

Resolved! Making Video calls from VCS using CUCM

HiCan a endpoint registered to VCS make a external video call using cisco gateway registered to CUCM.Scenario : C40 -> VCS -> CUCM-> Cisco 2900-> E1I appreciate any inputs regarding this

CTS1300 IP Phone show: System problem???

Dear all,I have two CTS systems (500 and 1300) in my office, and CTS-500 is registeredl with CUCM 8.0. The problem in CTS1300 is IP phone shows "system problem ???" , and both CTS1300 and its IP phone are registered to CUCM as well.I have tried to re...

TelePresence and Video Infrastructure

Forum Posts

Resolved! ISDN phone on Vic2-2Bri-NT/TE card

cisco services for migrated tandberg units

Resolved! Custom privileges for user, MSE 8510 blade

external audio calls from VCS through CUCM?

3241 ISDN GW backup D-channel using NFAS

Nortel Unistim

Resolved! Cisco VCS and IP Address Dialing

Resolved! MeetMe time limit

Resolved! Unable to make outgoing calls on Tandberg E20

Resolved! 2 Office VOIP design, and PVDM usage

Cisco Unified Video advantage

Number displaying

CUCM 7.1 sip to Tandberg MXP 3000

Resolved! Making Video calls from VCS using CUCM

CTS1300 IP Phone show: System problem???

Get ready! Great things are coming to Cisco Community

New name, same great product: Cisco Spaces

Congratulations to the July 2022 Spotlight Award winners!

Hiding the camera button on Webex Room Navigator

WebEx Room Bar - USB-C dual screen support

P60 Audience Camera Sensor Malfunction

Cisco Webex Codec Pro AD for centralized authentication

CMS - What causes the bad presentation quality? (Example attached)

CMS and S4B DualHome issue

RTMT versions 12.5/14

Connecting Laptop to cisco Deskpro using USB A to USB A

Webex Room Kit - Audio, but NO VIDEO in calls between endpoints

Webex PTZ 4K Camera Accessories