Dear all, Is somebody could give me the way to have the MPEG video flux of this 2 cameras please.I found the screenshot way but not the videohttp://ip/cgi-bin/viewer/video.jpgThank you & Best REgards,
We currently host an environment with 2 x CTMS servers hosting our multipoint meetings however we are likely to have a requirement to purchase one or more Telepresence server chassis' and appropriate blades. Given that the Telepresence server can ho...
I have a lot of C90s, E20s, 150 endpoints. I would like conferences of two or more to always use the Codian MCU.Can I do this with conference templates.participant template, or somewhere else?
Dear all, can anyone please give me an idea how to implement video conferencing .. dont have any idea how to do it ... we have CUCM 6.1.3, that can be used ot not .. with 3825 router. WAN options are Internet (ADSL) or ISDNPlease advise
When setting up two VCS' if you only setup one neighbor zone/search will calls complete? Or will you get a failure?Guess what I'm asking is does each side have to have a neighbor zone? Or if you want calls to go in only 1 direction can you just setup...
Besides the Web page on the C90 how can I upgrade it? I have a bunch of remote C90s and am worried about web browser timeouts.Q1. Can I use a USB drive with the USB port on back?Q2. Can I use the xcommand via ssh to tell it to upgrade via ftp, etc?
Hi,I use the SPA3102. Incoming calls come in via the PSTN line and outgoing calls leave via the internet. Out going calls, I have no problems. With the incoming calls I get a crackling/hissing line. I've checked my PSTN Line without the SPA3102 and i...
Newbie here! Camera is not sending video nor can video of other locations be seen on the monitor of one of our Tandberg units..audio is working. Screen is just showing a icon of a phone with the word STREAMING on it. This is not a newly setup unit....
Hi all,I have some trouble when connect from Tandberg 3000 MXP to Cisco MCU 3545 while working well with Polycom 9004. I've allowed all at ASA firewall.Please give me some ideas to troubleshoot this issue, thanks all!Regards,Khoavd
hello,1. cannot register by add device manually while auto reg is ok2. ip phone connecting to codec cannot display telepresence screen (codec cannot detect ip phone)3. there is no WebEx config option on cts manager server (License ?)Any tips will be ...
Hi Community,In the Codec C Series, is possible to connect 2 LCDs simultaneous without dual display licence?I just need to project the conference in both LCD's.Best Regards,Pedro Vasques
Dear all,I hope someone can help meWe use internaly VOIP and exetrnaly we have a PRI lineWe have a Cisco 3725 voice gateway and two Cisco Call Manager 5.1.I would like to know if it is possible to map a different number on an inbound caller id .Exem...
Does anyone know of a solution to record the audio portion of a call between 2 IP phones with VT Advantage? We have voice recording through verint. When we set up VTAdvantage and call, the verint recorders get start and stop signals, but no audio. ...
I think I have configured it all correctly and I have viewed the netcraftsmen website but it differs a little. When I run a sip trace from Media-fone5 i see an error : Warning: 399 (CUCM name) " Line not Configured" I can not find out what line need...
Hello, everyone. The company is considering to upgrade our CallManager 4.2 to CUCM 8. I have some questions: 1, should I upgrade the current unity 4 to Unity connection 8? Is unity 4 working fine with CUCM8? I am asking this because we think this ca...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
