TelePresence and Video Infrastructure

Meeeting Place Express and Tandberg Video Conferencing

I have been tasked with intergrating an existing Tandberg 880 and Tandberg 880 MXP with Meeting Place Express 2.x. I am unable to get video from or to the Tandberg cameras when participating in a Meeting Place Express meeting. If anyone knows what I...

Dial-peer not matching ?!?! strange. help please!!!

Hello there,I am having problems on matching my outgoing dial peer, the one i Dont want takes over you may say.i dial to 8018xxx33 would like dial peer 8187061 to be the one, as a better destination pattern, yet dial peer 22 takes over out of the blu...

Resolved! Is it possible to block incoming calls on voice gateways or CCM?

We have CCM V4.2 and Cisco voice gateways-Cat6k version 12.4Is it possible to block incoming calls by caller ID on voice gateways or CCMs?

CUBE on 2611XM does not register with SIP provider

Hi, I'm trying to register my 2611XM (c2600-adventerprisek9_ivs-mz.124-23.bin) with my SIP provider to make in and outgoing SIP calls to CUCM6. But whatever I try, my CUBE does not register with my SIP provider. Does anyone now what's wrong?Best rega...

VideoConferenceManager

In the installation of the Cisco Video Conference Manager is necesary the installation of the Cisco Unified Videoconferencing Desktop ?

VOIP drop after 2 times dial tone

customer complain when call from branch1 to HQ, it drop after 2 times dial tone. But is working fine when HQ call to branch1. And it also working fine when branch1 call to other branches. What step we take to isolate the problem? and what is the most...

CallManager integrate with Polycom RMX

We've installed Polycom RMX 2000 (version 3.0.0.94) MCU and wish to integrate with CallManger (version 4.1(3)) which acts as a conference bridge. We've tried to configure H323 gateway in CCM, but call just ring without answer. In RMX console, it show...

Cisco GW to Nortel PBX

I have a cisco GW connected to PBX Nortel, whe I make a phone call from the ip phone it travel to the ccm-GW-PBX-ISP.It always take the channel 31, and then I tray to make a second call and send a busy tone.Then if in the timeslot I change the 1-31 t...

Telepresence equipment freight weight + measurements

Hi! I'm working with a design of Telepresence installations and for import/export rates calculation I need the exact freight weight and measurements of each CTS system, that's CTS-500, CTS-1000, CTS-3000 and CTS-3200. I've read all the datasheets ava...

VoIP and VPN

Hello,I have a question about some voip/vpn configuration. I've got two sites that have 1760 routers with fxo/fxs cards that are going to be tieing the two phone systems together with a couple of voip trunks. These are secondary devices on the netw...

What do I need....

Hello,at the moment we have CME with some VT ADVANTAGE Clients. In the future we want to make Video conference with several of Users ( I think 10 Users at one Conference is the maximum). What do we need to realice this ? Many Thanks !!!!

mls qos trust "cos or dscp" ?

I have an uplink from an access switch configured as a trunk 802.1q that needs to trust Qos towards the distribution switch, does this have to trust cos or dscp ? the issue is that the access switch has a local voice vlan and the trunk uses another v...

Multipoint video conferencing with CM 4.1(3) ??

Hi guys,I am not looking to upgrade my CMs to version 7 until the next financial year i.e 6-8 months away but the business is looking for a multipoint video conferencing solution sooner than that.My understanding is the newer MCU devices are not comp...

Seting up a multicast server

Hi,I have a windows media server. For some reason, i'm only able to stream unicast streams from that server. I want to know if a device (router or server) can get the unicast stream from this server and multicast it over the network. It will be my ...

CM Discard Digit Instructions Not stripping correctly

I have a route pattern that would like to strip down to 10 digit dialing but it doesn't remove the 1.Test phone number is masked for privacy.Details:1. CallManager ver 4.1.3sr5d2. No recent changes to route patterns. We did rearrange CSS and PTS to s...

TelePresence and Video Infrastructure

Forum Posts

Meeeting Place Express and Tandberg Video Conferencing

Dial-peer not matching ?!?! strange. help please!!!

Resolved! Is it possible to block incoming calls on voice gateways or CCM?

CUBE on 2611XM does not register with SIP provider

VideoConferenceManager

VOIP drop after 2 times dial tone

CallManager integrate with Polycom RMX

Cisco GW to Nortel PBX

Telepresence equipment freight weight + measurements

VoIP and VPN

What do I need....

mls qos trust "cos or dscp" ?

Multipoint video conferencing with CM 4.1(3) ??

Seting up a multicast server

CM Discard Digit Instructions Not stripping correctly

Get ready! Great things are coming to Cisco Community

New name, same great product: Cisco Spaces

Don't miss the August 2022 Spotlight Award winners!

DCM D9902 SSD replacement

Unhealthy to turn off the Cisco Room Kit Plus on the weekends

Create Multiple Admin Users

Cisco Meeting Server User URI part assignment

Room navigator doesn't pair with Room bar

CS-DESK-LE-K9 Wifi details

CABLE PART LISTs For WEBEX and SX/MX endpoints

Need to change the CMS url

CMS and S4B DualHome issue

RTMT versions 12.5/14