Hello,Has anyone been able to register a C40 (or C60 or C90) to an Aaya Aura Communication Manager 6.x, using the H.323 protocol?I'm looking for a reference to know if it's been done before.regardsAvner
Hello,Has anyone been able to register a C40 (or C60 or C90) to an Aaya Aura Communication Manager 6.x, using the H.323 protocol?I'm looking for a reference to know if it's been done before.regardsAvner
I have a customer with two different entities. Normally they cannot touch. They each have VCS Controls and endpoints are registered to CUCM on one side, and the other side has them registered to VCS C. The endpoints on the side that are registered to...
Hi, We are facing issues for video conference units like codec are receiving calls from unknown locations and unknown numbers . when i search solution someone is saying this is a spam. The thing is some site codec is directly connected internet , i...
I got a new DX 80 and after powering it up, it boots and ends up with 'Unfortunately Status MessageLocationService has stopped' message. It doesn't allow me to create a problem report. I tried to factory reset by holding the up volume key but I did ...
I have a Cisco TelePresence SX20 software 7.3 Do I need an option key for dual display? Or is this a standard feature?
We have an sx20 that we registered to call manager 9.1.2. we have an ex90 that is tied to our Tandberg gear due to a grant requirement. Is there any way to get those devices to talk to one another, outside of moving the ex90 over to CUCM?
Hi, Can you help regarding on this issue. Our client has EX60 registered in VCS before. Client decided to registered it on CUCM but before that client performed a factory reset on the EX60. Now, EX60 is not registering in CUCM. CUCM version is 9.1. A...
I am looking for the setting to enable an endpoints name to be displayed (Example CEO Office ) during a video conference. I cone through the SIP settings and saw a field for system name and added but the particular endpoint doesn't display its name d...
Hello everyone, I have recently deployed Cisco Conductor XC4.0 to integrate with CUCM version 10.5.1. I have deployed the Conductor as per the CUCM and XC4.0 design guide, the certificates have been added, all SIP trunks are Registered. Everything lo...
Hi I'm trying to find if there is a limit in the content server with regards to recording aliases. How many recording aliases that are linked to users can be created in the content server ? In the documentation I did not find that information Thanks ...
Hi everbody, i have a short question if the scenario i am going to explain is possible, and if, how we could achieve this. We are planning to deploy a third party UDS Phonebook to some endpoints and it already runs fine when the endpoint, that uses i...
we will change ip address of TMS what i have to do after change the server which TMS install on it, and for the TMSXE how i can change the TMS old ip address on TMSXE server.
Hello, There is a dx20 with the multisite license. Need to know if DX80 to participate in a video conference with DX20?
Hello Every One. I Need to know, how we can extend the HDMI Camera Cable and the DSUB/RJ45 Camera Control cable up 50m. we know that the HDMI cab be extended using commercial HDMI Extender but we don't know if the C60 uses standard HDMI signal. and w...
Hi can I use the sx20 camera as a usb camera with other device? can I disable the light sensor of the camera? and can I make the camera go back to the original position and zoom/focus after it lost it the power? thanks shy
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-30-2024 01:34 PM | ||
10-29-2024 11:00 AM | ||
10-25-2024 08:22 AM | ||
10-06-2024 09:05 AM | ||
10-04-2024 06:18 AM |
User | Count |
---|---|
1 | |
1 | |
1 | |
1 |