We have a SX10 camera, touch 10 control panel and a 65in tv. is there instruction on how to set it up for using Webex and Microsoft Teams.
We have a SX10 camera, touch 10 control panel and a 65in tv. is there instruction on how to set it up for using Webex and Microsoft Teams.
I can't set up 802.1x from Touch 10 on cisco sx80
This installation has a Webex Room Kit EQ running as a Microsoft Teams Room (MTR)The Room Kit EQ is connected via USB A to a QSC NV-31-H for audio.I have audio in and out of the codec. i am able to adjust the system volume on the 'cisco' side of the...
Hello, I am having an issue with configuring my Webex. I log into the unit through a network fine at my test bench. I then proceed to change the configuration in the Settings tab. I save every change I make just in case I time out. Once I have made a...
Hi, all.Greetings. I have two Cisco room kit EQ with Quad camera then found difference when setting 'zone' setting.One has zoon as below.The other one shows four blue corners. The issue is ; with those four blue, camera simply doesn't show when in au...
Good Morning my site just stood up a VCS-C and VCS-E on our classified network. We are receiving terrible audio latency but good video on our calls no matter if we are pointing to our neighbor peers or to our CMS Bridge. I checked the endpoints durin...
Hi there,I have the following notice on control Hub for my Cisco Telepresence SX80 Codec:"This product is obsolete and will be disconnected from all cloud services. Technical support, software updates, and hardware replacements have been discontinued...
I know there are calcs for switches to calculate power. However, is there a calc that I can use for Routers, and MCS devices? I am specifically looking for AMPS/WATTS draw, Heat Diss., etc
Hi,I made a CMS cluster, CMS-A and CMS-B (CMS-C is only DB). The video endpoints registered to CUCM.If I call from a video endpoint(9206) to a virtual meeting room (address: 2005) and the call is replaced from CMS-A to CMS B, the call is ringing but ...
Hello - I trying to see if it is possible to configure the audio console on a WebEx Codec Pro using Macros.The customer has a CODEC Pro with 4 Microphones and 2 speakers "Zones" in a kinda large extremely packed acoustically challenged room. Phase 2 ...
Dear CommunityDoes someone knows on when sip condition expressways jump to next search rule after routing to a zone?Assume that "on successful is configure to "Continue".For example assume you send a sip invite to a neighbor zone and zone replying w...
Hello community,one of our customers wants to control the AV system and in room functions from the Cisco Touch 10.In fact, there are two Touch 10, one in each room.We use Extron control, a driver for the Touch 10 is available, so far so good.Based on...
I have cisco meeting server 3.9 and cisco meeting management 3.9, I configured meetingapps for file-sharing but this feature for role that I configured in cisco meeting management not visible, with space default Role this feature is visible.
My Expressway logs show this event once per second:traffic_server[16496]: Event="Sending HTTP error response" Status="400" Reason="Bad Request" Dst-ip="127.0.0.1" Dst-port="30054" UTCTime="2020-10-15 15:59:52,083" I don't have any issues with how thi...
We are having issues getting Miracast to work properly on Cisco Kit EQ units in our organization. The function works fine on Room Bar Pro units, but when attempting to start sharing on EQ, we get a message "Something went wrong" and the device does ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-02-2025 07:37 AM | ||
06-18-2025 10:21 AM | ||
06-17-2025 05:26 AM | ||
06-06-2025 12:26 AM | ||
06-02-2025 07:45 AM |