Hi,Any procedure to recover admin password for cli and web adminhttps://ipaddress:445 or is there any other port to access web appThanks
Hi,Any procedure to recover admin password for cli and web adminhttps://ipaddress:445 or is there any other port to access web appThanks
Hi,So we are trying a new deployment for WebRTC via expressways from different locations using different URL/webbridges on same CMS" node.the problem is that with multiple Turn Server "local expressways-E" configured on CMS, the Turn servers are assi...
HiI have cms 3.0I would like to know if it is mandatory to mannualy assign a PMP license to LDAP users or the CMS is responsible to assign PMP license automatically to LADP users when they connect and keep PMP free when thos user disconect then reass...
We are installing an Expressway-E with the capacity of B2B calls, but when it calls from internet to expressway public IP the call shows "unreacheable". the log, only shows: Search (275) State: Completed Found: False Reason: Address Incomplete ...
We have a new deployment of CMS 3.0 and TMS 15.12, with TMS scheduling "Automatic Connect" conferences to VCS X12.6.2 registered endpoints (CE9.14.3, TC7.3..). We have had multiple reports of CE9.x endpoint users muting themselves, then being unable ...
We have a few WebEx DX80’s that staff want to pair Bluetooth headsets to, but the option settings aren’t available. In this case:The headset is a Jabra 75 [Supports: A2DP (v1.2), Hands Free Profile (v1.6), Headset Profile (v1.2), AGHFP (v1.6)]The sys...
Our IX units have their timezone set to "Current timezone: Australia/Sydney" which is UTC+10:00 but the logs appear to be in UTC+ 00:00. Can the log timezone be change? Software Version: 9.1.1
I am using TMS with CMM. Is there a way to input DTMF tones?
I recently installed a new out of the box Codian 4220 Software version 4.1(1.51). I got it working with no visible issues. Then I sent to CISCO downloads and copied the 4.5(1.71) file. cisco_mcu_4200_4.5_1.71.zip. I also used the release notes and f...
Can HDMI output 3 of the CS-CODEC-PRO+ be configured to show ONLY the near end video currently selected by the TOUCH10 controller controlling the codec? Thanks
Currently we have Teams enabled meeting rooms. When I book a Teams meeting in either one of two particular rooms in outlook, I get the response back which says the meeting is accepted. Then about a minute later an email comes back and has the error: ...
Need a refresher please. I am at a new site running TMS 15.12.0. I need to pull reports over 90 period. When I run the report it tracks only for a week of data even when I set the start and stop date. What options should I increase in the log to k...
Anyone have a doc on steps to replace the SUPVR card with new one? Can it be done hot swap ? If not I assume take back up of config shut down the MCU swap the card power up remote in and restore config ? Thanks.
I've got a weird issue with a VCS-C cluster. I have two nodes running X12.6.2. Node 1 is a "cluster of 1" with itself defined as peer 1 (using IP address, everything set to permissive).When I add peer 2, they cluster OK and peer 2 grabs all its con...
Hello, We have a CMS recorder (version 2.8) which is configured successfully to save recordings into a shared NFS folder.We want to configure VBrick Rev/DME to read the files from the shared folder, delete them from there and save them on VBrick Rev/...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 08:22 AM | ||
04-25-2024 05:00 PM | ||
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM |