Unified Communications Infrastructure

Permission to use BAT in CM 7

Communications Manager 7.1(5)I would like to setup limited access for contractors who wiill only need to use BAT. But it appears that I will have to give these users Admin rights to users inorder for them to be able to use BAT. Does anyone know of a ...

UNITY connection

HI, I feel comfortable with unity server and its working softwares, architecture etc., Can anyone 1 help me with unity connection because it runs on linux and i want to have lucid picture about this.

Error occurred. One or more record did not get deleted. [4920] Licensing checkin failed (checkin count is greater than checked out count)

Hi,I'm using a Cisco Unified Communication Manager 7.0.2.10000-18 installed on VMWare ESXi 3.5 system Server. I have a default based license as 150 devices. I have used all 150 licenses and i try to delete some devices ip phones to have free license ...

Bypass Meetingplace 6.x "To attend a meeting, press 1" prompt

Ok, we are running MP 6.x - i just upgraded to MR5, however in MR4 we had it set so that when you called in to attend a meeting you did not get the initial 'To attend a meeting, press 1' prompt (i believe this is voice prompte #149). Now that i have...

Unity Licenses

Would like to ask the following questionIf I have an Unity server and wanted to increase my number of licenses thus needed to purchase for that.The Unity Server is 5.1 but the licenses to be purchased is EOL (end of life).Is it ok to purchase Unity S...

Visual Voicemail is supported by 6921 ip phone model?

Hi all,I want to know if Visual Voicemail feature is supported by 6921 ip phone models on new version 8 of Unity and Unity Connection. I have found some information but I am not able to confirm this point and I am a bit confusing.Thanks by advanceFer...

Cisco Mobile 8.0 Desk Phone Integration and another issue...

Hello,I am trying to setup the Cisco Mobile 8 app on my iPhone according to the Administration guide. The first issue that I am running into is:When a call comes into my desk phone, my iPhone will ring once and that's it. The call then doesn't ring...

CISCO unified Mobility Advatage problem

Hi ,I try to install CISCO unified Mobility Advantage 7.1 in VMware 7the specfication in VMware : Mem 1024, Hard 120G IDE, 2 Processor, Network bridgedand I already add the name & ip for CUMA server in domain and DNSand every thing is ok in installat...

Unity upgrade 4.03 to 7 ADschema update

Dear all,I would like to know if it is possible to run Adschema update for Unity 7.0 when Unity 4.03 still online.Thank you for your helpRegardsMaissiat

Resolved! IP Contact Centre version 7 capabilities

Good Day All,We use IP contact centre version 7.We have a simple script that queues customers during the day and shunts them off to voice mail after hours.Our customers who have an after hours agreement need to dial a different number after hours for...

CUPC 7.1 addin breaks outlook after kb2293428 patch is applied

On our Windows XP sp3 with outlook 2003 once the patch is applied and the addin is enabled. You will get the "Outlook has encountered a problem an needs to close" when you launch outlook. Outlook will not launch untill you disable the addin.Any ideas...

Resolved! Cisco Unity Connection Architectural Overview

Hi,Does anyone have the Cisco Unity Connection Architectural Diagram.The architectural diagram for Cisco unity is available and we have Cisco Doc written by Jeff Lindborg for the same,but I am not able to find the Cisco Unity Connection Architectural...

Can MCS-7835-H1-CC1/ECS-1 run CUCM 7.1(5)?

What do I need if in the near future we want to use CUCIMOC and CUMA?Regards,Dennis

Resolved! Single number reach, cell software ?

Hi all experts.If i configure SNR on CME 7.1, do i need to install any software on nokia (or other brand) cell phones ? as far as i understand the configuraton, i dont think there is any need for it. Just want to confirm.thanks in advance

Resolved! CUCM Subscriber status error 4

Good Day,I have a CUCM 6.1(2) installed. If I do a " utils dbreplication status " the publisher shows status 2 ok. The Subscriber shows status 4.We re-installed the subscriber the second time now and also removed and added the server to the publisher...

Unified Communications Infrastructure

Forum Posts

Permission to use BAT in CM 7

UNITY connection

Error occurred. One or more record did not get deleted. [4920] Licensing checkin failed (checkin count is greater than checked out count)

Bypass Meetingplace 6.x "To attend a meeting, press 1" prompt

Unity Licenses

Visual Voicemail is supported by 6921 ip phone model?

Cisco Mobile 8.0 Desk Phone Integration and another issue...

CISCO unified Mobility Advatage problem

Unity upgrade 4.03 to 7 ADschema update

Resolved! IP Contact Centre version 7 capabilities

CUPC 7.1 addin breaks outlook after kb2293428 patch is applied

Resolved! Cisco Unity Connection Architectural Overview

Can MCS-7835-H1-CC1/ECS-1 run CUCM 7.1(5)?

Resolved! Single number reach, cell software ?

Resolved! CUCM Subscriber status error 4

Get ready! Great things are coming to Cisco Community

How Cisco TAC is transforming documentation and self-service

Congratulations to the July 2022 Spotlight Award winners!

8800 series MPP phones line key icon

Bulk Editing in Unity Connection

CIsco Vendors and Silent Monitoring/Whisper Coach WITHOUT UCCX

Flex-CUBE License

Unity Connection upgrade from 10.5 to 12.5 no valid upgrade options

How to get a new license for expressway in cisco software portal ?

Deciphering Unity Version

Can I have more than 1 Unity Connection Subscriber in a cluster?

Cisco Unified Attendant Console - users being logout automatically

Cisco CME voice mail configuration