cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2174
Views
0
Helpful
6
Replies

FAC on CME 8.5

jmarshall9529
Beginner
Beginner

Has anyone been successful in deploying FAC on CME 8.5 using lpcor?   The solution I want is flat all external calls would require a FAC.

2 ACCEPTED SOLUTIONS

Accepted Solutions

mdawar
Cisco Employee
Cisco Employee

Following document talk about FAC on UC500. Should be good for CME.

https://supportforums.cisco.com/docs/DOC-9795/

View solution in original post

asandborgh
Enthusiast
Enthusiast
6 REPLIES 6

mdawar
Cisco Employee
Cisco Employee

Following document talk about FAC on UC500. Should be good for CME.

https://supportforums.cisco.com/docs/DOC-9795/

asandborgh
Enthusiast
Enthusiast

Hello ALL:

I used the 8.5 Guide to implement the FAC with lpcor.  Currently if an lpcor is accepting calls from another group eg accept X, when I add accept X fac the calls go to a fast busy.

Any help really need to expedite the process.

!

voice lpcor enable

voice lpcor custom

group 10 Manager

group 11 LocalUser

group 12 RemoteUser

group 13 PSTNTRunk

group 14 IPTrunk

!

voice lpcor policy PSTNTRunk

service fac

accept Manager fac

accept PSTNTRunk fac

!

!

!

!

!

application

package auth

  param passwd-prompt flash:enter_pin.au

  param user-prompt flash:enter_account.au

  param term-digit #

  param abort-digit *

  param max-digits 32

!

service clid_authen_collect

  param uid-len 4

  param pin-len 4

!

!

dial-peer voice 4 voip

corlist outgoing call-cell

destination-pattern 00.........

lpcor outgoing PSTNTRunk

session protocol sipv2

session target ipv4:10.86.3.50

voice-class codec 1 

dtmf-relay sip-notify rtp-nte

no vad

!

!

!

ephone  3

lpcor type remote

lpcor incoming Manager

lpcor outgoing PSTNTRunk

device-security-mode none

mac-address DC7B.94F8.D8B4

type 7911

button  1:4

!

!

!

voice lpcor enable

voice lpcor custom

group 10 Manager

group 11 LocalUser

group 12 RemoteUser

group 13 PSTNTRunk

group 14 IPTrunk

!

voice lpcor policy PSTNTRunk

service fac

accept Manager fac

accept PSTNTRunk fac

!

!

!

!

!

application

package auth

  param passwd-prompt flash:enter_pin.au

  param user-prompt flash:enter_account.au

  param term-digit #

  param abort-digit *

  param max-digits 32

!

service clid_authen_collect

  param uid-len 4

  param pin-len 4

!

username 1984 password 0 1984

==================================================

calls to the pstn

==================================================

!
!
ephone  3
lpcor incoming Manager
lpcor outgoing PSTNTRunk
device-security-mode none
mac-address DC7B.94F8.D8B4
type 7911
button  1:4
!
================================================================================

When this phone try to place outbound calls will be prompt to enter account and pin then tha call will be allowed

=================================================================================

!


dial-peer voice 4 voip
corlist outgoing call-cell
destination-pattern 00.........
lpcor outgoing PSTNTRunk
session protocol sipv2
session target ipv4:10.86.3.50
voice-class codec 1 
dtmf-relay sip-notify rtp-nte
no vad
!

Hi All:

The issue was not the overall implementation but a trunk group that was being used. The guide pointed to applying the lpcor to the voice-port but when you use a trunk group you have to apply the lpcor under the trunk group settings for it to be effective.  I had resolved the problem and the customer is now working fine.

It was actually when the customer requested a connection to a VoIP provider using a single port, that I was able to solve the problem.  Thanks guys, not surprised you didn't see it as I had about 3 cases with TAC and they wouldn't solve it.

nizarkotakkal
Beginner
Beginner

Hi,

 I need to apply FAC for a user, but only for the calls begin with the digit 0 (for international) . All the calls beginning with any other digit should go without asking FAC.

 I am giving my dial peer configuration below.


dial-peer voice 124 pots
 trunkgroup ALL_T1E1
 corlist outgoing call-international
 description **CCA*INTERNIONAL**
 translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
 preference 3
 destination-pattern 9[0-9]T
 forward-digits all
 no sip-register
!

I want to aplly the setting for the user using this dail peer.

 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: