Hello,I have a problem with a Cisco C240-M3 server.The front panel LEDs all light up green, the LED (D21) on the motherboard lights up permanently orange. Tested DDR3 4GB ECC Ram is in slots A1 / B1 and E1 / F1.Problem, the server is not starting.I w...
Forum Posts
Resolved! UCS on Cisco HyperFlex HX220c M5 Node
Hi,We recently purchased 3 copies of the machine listed in the contents.Well, as expected, we quickly broke, now you need to reconfigure the UCS ...Since we didn't set up this cluster, we have no idea how to even go into UCS, the guides and guides pa...
Hi Team I know this question was asked several times in the discussion, but I was not able to find answer for my question. I am recieving test email from Cisco IMC but would like to know how do i configure if any critical alerts triggered and send th...
Is there anyway to manage the CIMC from the Operating system (as there is with HP ILO)?
Resolved! UCS C240 M4 keeps booting into BIOS
We have 3 servers with a fresh Ubuntu install on each server. I did a "shutdown -r" and rebooted the server. Now it seems to be stuck in the Aptio setup (BIOS) utility. I either choose "save and exit" or exit without saving changes and I am brought r...
Resolved! Replace running C220 with new server RMA
Hi, We have a running C220 with a problem in VGA interfaceWe do RMA and the new server arrive We have ESXi with Vcenter, hyperflex VM and other windows server VMs running on the old serverIs it simple to move the HDDs to the new server with the same ...
Hi there, I'm looking to update the firmware on some old stand aloneUCS 220 M3S that are in our lab (to hopefully close off some CIMC security holes that were found) but when I connect to the KMV and mount the iso they don't seem to show up as a boot...
Hi Experts,I need a point of clarification, and if anyone would be so bold as to SHOW me a way to pove this point, I'd be extremely grateful.The point in question is the order in which a Hyperflex controller seeks the target information for a Read Re...
Has any other people experienced F0397 issue on FAN module of UCS C220M5? We upgraded all old C200 and C220M2 to M5 from 2019 for all global sites, but has been reported failure for 5 times after ~1y, some sites report more than one FAN module fail.
I'm working on migrating a UCS and I see that somehow the KVM of the servers have two IP addresses. One is from the service profile and the other says equipment derived. What mechanism yields the equipment derived IP address? I want to have only one ...
Resolved! BE6M-M5 firmware
Hello, I am trying to upgrade the firmware on some BE6M-M5 servers. From what I understand, these are c220 m5 servers, but trying to apply the firmware regardless of the version results in a soft lockup as seen in the image. Any ideas what is wrong...
I am migrating a UCS from one data center to another. I found that the mac address pool and external mgt IP address pools have overlap. What I want to do is shut the existing blades. Remove the current mac and IP pools. Then I want to turn up the bla...
Resolved! Can a UCS FEX be removed or added live?
I am migrating from one FI pair to another. The current FIpair has a 16 port FEX module in them. If I remove all theEthernet connection from them, can I remove the FEXmodule from a currently running fabric interconnect? Andon the flip side can I inse...
Hello Experts, The customer's one B200 M5 Blades Status LED is blinking GREEN.Is there any estimated cause of this behavior? Best Regards,
Resolved! Role of the Native VLAN for UCS vNIC
Preparing to migrate a UCS from one location to another - I noticed that the ESX/blade management VLAN 101 is checked as being "Native". However if I look at the switch side of the uplink ports there is no VLAN 101 assigned to be native for those tru...
