About cisco-newb

cisco-newb · 12-19-2019

I have a 2960 switch with 'ip routing' enabled, I did run 'sdm prefer lanbase-routing' followed by a copy run start and a reload. IP Routing is enabled. Here is the setup: pfsense router- LAN, 10.25.25.1 /24- LAN2, 192.168.33.1 /24- pfsense has an ou...

cisco-newb · 11-26-2017

I tried to log into the switch and I was prompted with a user/password is incorrect message. I have been using a password manager for several years and the credentials for this switch have been in the manager since day one. I logged in and made a cha...

cisco-newb · 10-13-2015

I installed a cisco sg300-28pp with a few vlans. Not sure that the vlans matter, but it doesn't hurt to include that information. Basic setup (my opinion), 1 vlan for regular network traffic, another vlan for guest wifi (this is in a small business) ...

cisco-newb · 08-07-2015

I am in the process of setting up this switch and I have a few questions regarding the smartport and voice vlan (default tagging).1. If I am not using any other cisco devices and not needing LLDP (and CDP) is it safe to un-check/disable those options...

cisco-newb · 08-04-2015

I seem to have an odd issue with this brand new switch that I purchased a couple weeks ago. I am using this switch for IP Cameras and other PoE and PoE+ devices and so far everything appears to be working as expected (still staging equipment/cameras...

cisco-newb · 12-20-2019

@paul driver wrote:HelloThat more specific default route on the switch just cuts down on any possible recursive router and unnecessary arp queries icmp would no doubt be disabled on the Fw so not really worried about a successful ping to/from FW so t...

cisco-newb · 12-20-2019

@Georg Pauwen wrote:Hello, for the sake of testing, try and disable the Pfsense firewall completely, in order to rule out that your firewall rules are causing this issue...I don't want to completely disable the firewall, but I'll try a packet capture...

cisco-newb · 12-20-2019

edited-ignore, I made a mistake. will delete the post, if I can.

cisco-newb · 12-20-2019

Ok, I will add the NAT. I assumed once the switch traffic had a route to get to the pfsense, the route accepting the traffic from the switch would be the only network needed for NAT, in this case, the 10.25.25.0 /24 network, which a NAT does exist fo...

cisco-newb · 12-20-2019

I have DNS defined on the switch to confirm connectivity to the internet, from the switch CLI, but I could just ping 8.8.8.8 instead of google.com, however, I see what you are getting at. I do not have a NAT rule for VLAN 100 on pfsense, I didn't thi...

Member Since	‎08-04-2015 11:15 AM
Date Last Visited	‎09-06-2023 12:27 AM
Posts	23

User Statistics

User Activity

cisco 2960 running two VLANs, can't route/get out of local networks (pfsense router)

password reset for sg300-28pp

Odd issue, wondering if anyone has experienced this, before.

smartport and voice vlan question

sg300-28pp ports not always lighting up/active

Re: cisco 2960 running two VLANs, can't route/get out of local networks (pfsense router)

Re: cisco 2960 running two VLANs, can't route/get out of local networks (pfsense router)

Re: cisco 2960 running two VLANs, can't route/get out of local networks (pfsense router)

Re: cisco 2960 running two VLANs, can't route/get out of local networks (pfsense router)

Re: cisco 2960 running two VLANs, can't route/get out of local networks (pfsense router)