The online documentation refers to a Blind Transfer (BlindXfer) softkey, but our phones don't show this during calls. Does this have to be programmed in? Thanks.
The online documentation refers to a Blind Transfer (BlindXfer) softkey, but our phones don't show this during calls. Does this have to be programmed in? Thanks.
We deployed 100+ SPA502G/SPA504G phones. Some users have problems with the soft-buttons:On call the "xfer" button disappears and only a "Conf" soft-button is showing in the middle of the display. Users can't transfer a call anymore.This happens now...
We use MetaSwitch for our phone switch. We have a HPBX for a local small business. A caller calls into the HPBX with a MLHG via a pilot. The secretary is not at her desk so using the "Monitored Extension" a second person presses the secretarys button...
The scenario is like this, when user press the soft button on the phone and set the number to be forwarded. The number will not be updated in CUCM 'call forward and pickup settings' so any call to the phone can't be forwarded. When I tried to call th...
Can I use my SPA504G phones with a Cisco 2911 router....I mean is this even possible...if so then I will ask how! Thanks Don
Hi, First off, I'm a bit of a novice at stuff like this. But this is something I need help with. I have a Cisco SPA122 that we use to "digitalize" our Faxes and doorphones and stuff like that. I need to deactivate the port Line 1 when I loose Intern...
I have a new BE 6000 someone ordered from CDW. The UCS is p/n UCS-E160D-M2/K9. According to the setup documentation I should be able to attach a VGA monitor and USB keyboard and be well on the way. However, when I attach the monitor there is no ...
UC540 running 8.6.2. I installed IOS on blank formatted CF card (FAT) using the TFTP method. uploaded and updated the running-config. Cue was also reinstalled. Problem is inside of CCA it shows flash capacity as "unavailable". I cannot update the s...
I have a new install UC540W I have setup 8 extensions 201 thru 208 using spa508 phones I have 3 inbound pot lines. setup call park extensions as 701 and 702 when I have a inbound call and I try to park it it gives me a unknown number and a busy signa...
I've tried reloading and installing with the boot helper, but everytime I session to it I get this error:ReiserFS: warning: is_tree_node: node level 0 does not match to the expected one 3ReiserFS: hda1: warning: vs-5150: search_by_key: invalid format...
I am trying to connect a cisco pbx system at one location to the phones at a different location. I am using vpns. I have something wrong because the remote phones cannot get to the CM. I have tried setting the phones to static IP addresses (20.x and ...
Hi, Can someone tell me how to lock down my SPA 112 to the specific IPs used by my SIP provider? They have 2 IPs. I want all other incoming traffic from other IPs to be ignored. Thanks
1. Will the SPA112 work with an LTE cellular router? I'm currently getting about 20 Mbps up and down on our LTE router via a cellular connection. 2. If so, will faxes work on the SPA112 on an LTE cellular router? The one we have has a voice jack, but...
I create case ID: 638671195. We have a problem with the SPA8800 configuration. Logical topology: CUCM <-> Asterisk <-> SPA8800. Firmware on device 6.1.11(XU). The configuration files in the attachment. The problem is not permanent. These three conne...
Hello, I'm trying to connect the SPA9000 to a PSTN-line wit a SPA3102. I've got the incoming calls (on the pstn) to work but the outgoing calls not. The Line1 of the SPA9000 does not get registered. (fails with error: 'SIP:ICMP Error -1 (c0a80005:606...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: