Hi all, If my UC560 is configured using CCA and then I want to make changes using CLI( assuming that CCA is not available on laptop) , is that supported? Regards Sriram
Hi all, If my UC560 is configured using CCA and then I want to make changes using CLI( assuming that CCA is not available on laptop) , is that supported? Regards Sriram
Is there any reason that these phones will not work on BE6K 10.5? I just cant seemt to get them to register! Download XML.Dfault.cnf.xml is stuck in the display. Does this file come from CUCM or the Router? I know on the old UC500 they downloa...
Outgoing to cell - I can hear caller, they can't hear me. incoming from cell - OK Outgoing and incoming to/from UK landline OK Outgoing to PBX- I can hear caller, they can't hear me. Incoming from PBX- not tested What could be the possible cause of t...
UC320W listening 5064 port on WAN and any desirous can use your device as SIP proxy! | SIP Device | User Agent | Fingerprint |-----------------------------------------------------------| X.X.X.X:5064 | Cisco/UC320W-2.3.3(4) | disabl...
I have a spa112 phone adapter and linksys EA4500 router and i am having problems with no audio on phone calls. The person at the other end can hear me but i can't hear them. I am curently using freephoneline.ca. I had it working for two years until i...
Hello, I am trying to update two SPA504G phones because hopefully it will make the MWI light go off after I have listened to the voicemails. The red MWI alert stays on, so does the envelope indicator on the screen along with the intermittent dial to...
I have setup my new SPA112 with a EdgeRouter. Router config: Forward port 5060-5061 to SPA112 Forward port 16000-17000 to SPA112(also tried 10000-35000) SPA112 Config: NAT: EXT IP, Keep Alive (my ISP doesn't use a STUN server, tried another STUN se...
I have a spa525G2 using SIP at a remote location which needs to register to a TFTP server over the Internet.The remote locaiton does not have a TFTP server or option 66 or 150 in DHCP, so I want to either hard code the IP of the TFTP server in the 52...
Hello, I need to configure inbound calls from SIP provider to UC520 and then to CUCM 8.6.2 The calls do no go through, when a trace is performed the SIP Trunk Provider says UC520 replying with "500 internal server error" in response to inbound cal...
Hello I am configuring a UC320 and performed a factory reset, hold button 10 sec, won't restart now, Gui errors out, after login screen system shows ' intializing new config' it gets to 20% and errors out " error parsing XML data from input XML is mi...
WHAT?There is a known incompatiblity with Adobe Flash Player 11 and UC320W Configuration Utility running on firmware earlier than 2.1.2. This incompatibility prevents the UC320W Configuration Utility from loading. If a user tries to launch a browse...
Hi everybody I've just bought a second hand UC540. I've restored the factory defaults and it's now configured for my SIP provider and is working great in my small office with 4 7975 phones. I'm a developer and I would like to use TAPI/CTI to make a c...
I have an unlocked SPA2102 running the latest firmware (5.2.12). The date/time just get reset back to 1/1/2003 (I think) after a couple of days.It is hooked up to a UPS and there is no black out. It has been doing this for over a month. I tried the o...
Hello my bad English soryy sound from the handset as follows: https://drive.google.com/a/djalper.net/file/d/0BxYvJ8BVZ0ACZUMyaEMtSXg1MG8/view?usp=sharing I updated but not improvement
Hello everyone, I have a Cisco UC520 with one FXO analog PSTN line and a SIP Trunk. I am using custom Music on Hold which had been working great. I am not sure what happened but now anyone connected to the PSTN line will hear beeps rather than actual...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: