Voice Systems and Accessories - Small Business

Hi,I just bought a new SPA509G phone. I updated to the newest software (7.5.5) and I have it configurated the phone to work with our "local" Asterisk system.Requirement however is to work with some external sip accounts also, like my bosses home. We ...

Приветствую вас, Коллеги! Возникла следующая проблема (вариантов перебрал много ): Не могу правильно настроить исходящие звонки на PSTN из Asteriskа (VoIP-To-PSTN) (NeoPBX на базе Elastix 1.6, пробовал и Asterisk из портов версии 1.11.5) через шлюз ...

Hello Cisco support. I recently purchased the SPA122 and set it up. I am getting "incomplete data" as the call display for all incoming calls.Please can someone help me.ThanksBissoon

I have a customer with a UC540 and about five phones in his office.  He also has two remote phones at his home.  He prefers to work from his home.The office has Time Warner internet, and so does his home.A tracert from his home to his office is only ...

The new SPA122 device connected to router through DHCP. I can see IP-address on router's web page, can ping it, and receive it with ****110# IVR command. But I cannot access web configuration utility in the browser: the page is unavailible. I tried t...

Buongiorno a tutti!avrei bisogno dei consigli su come configurare il mio spa3102, per fare in modo che il mio telefono voip riceva ed inoltri chiamate su linea pstn.essendo una abitazione volevo sapere se era possibile fare in modo che oltre ai telef...

Salve, vorrei sapere come configurare l'apparecchio  spa3102 con un telefono voip snom 300, in particolare vorrei utilizzare il telefono voip per effettuare telefonate sulla linea analogia attraverso il telefono voip snom300GrazieSergio

Hi, I try to upgrade the firmware of a spa301 to 7.5.5, everything goes fine but when the phone restart the light goes orange and nothing happen after. I try the recovery firmware with the serial number but doesn't work. I can't do anything with the ...

Our telco (Virgin Media Business, UK) have asked for some information about the PBX (UC540) in order to correctly configure ISDN PRI (E1 - ISDN30) at their end. We have a VWIC2-1MFT-T1/E1 voice interface card installed in the UC.Specifically they wan...

Cisco, please let us have one last set of new fetures and bug fixes even through you ave announced end of life.  You have replied to so many posts saying that you are working on new firmware over the last year, but we have not seen anything yet.Can s...

Hi, I have a few SPA 8000 and SPA112 TA's, and everything's OK, until I tried to transfer a call from one of this analog lines, it doesn't work.For what I've saw on some info on the web, it's about configuration, but doesn't seems to work. I'm locate...

Hello everyone!I am having some issues with my UC560, when I try to call to the voicemail (499) and AA (500) it just has busy toneFrom the CCA i run a diagnostic and i recived the error messages attachedI just dont know what is happening. I already c...

I have a UC540 with the main line going to a hunt group but when the lines in the list on the hunt group are already on a call the line goes to voicemail without ringing. Is there a way to set it to ring even when the lines are busy? It is a logest-i...

Maybe I'm wrong on this one but you can't connect a UC560 directly to an amp (Bogen) without some kind of paging attendant device, correct?  One job we did, the customer already had an "AT&T Page Pal" which connected to the UC560 via an FXS port and ...