Voice Systems and Accessories - Small Business - Page 331

Resolved! UC540 - hunt group timeout resets

I have a customer with a UC540 system configured with a hunt group for 4 of the users. The hunt group is sequential and the timeout is set at 25 seconds. Approximately once a week the customer calls me to have me reset the timeout back to 25 seconds ...

UC520 SSL VPN Full Client package installation failed

I am trying to enable the SSL VPN - full tunnel feature in UC520.However when I try to load the .pkg file into the UC520, I've met with the error "Error in installing package file". (refer screenshot).How do I solve this issue or get the detailed inf...

Unable To Get Admin Access To SPA508G

We are running the UC320W and we have one SPA508G connected to it. When we try to access the phone via the web all works ok until we try to access the "Admin Login." We then get "403 Forbidden!."There is no option on the phone to allow admin web acce...

SPA9000 drops on hold call

Hi,I have searched the forum and not found the correct answer.I have a SPA9000, SPA400, SPA504g and SPA508g in a small office system.A call that is placed on hold with the SPA508g cannot be picked-up with the SPA504g phone. I can do the opposite only...

UC560 - SF2010P smart ports

HiWe upgraded an ESW 24 port witch to a SFE2010P 48 port switch on a cusotmer site with a UC560.We linked port G1 on the Switch to the Expnaions Port on the UC560 whcih the ESW was plugged into.With the ESW plugged in smartports wanted it set as a sw...

SPA504G choppy. But 7941's are not!

I deployed a UC540 and about 10 SPA505G's. For some reason all of the SPA504G's have a slight digitized noise periodically. I gave a few users some 7941's to try out and they said it's crystal clear.I've used the SPA504G's with non Cisco deployments ...

Can I duplicate phone button settings?

I have 14 phones all with side carts that need full programming. I was hoping to program one set then clone it to the rest. One idea I had was to program one phone then save the config to a cfg file on my computer and edit it by hand then restore t...

Cisco SPA303 -- Does not get any incoming calls, outgoing calls are also spotty

Does anyone have any experience with the issue mentioned in the title? I'm using a router with TomatoWRT firmware. I have forwarded the specified default ports with the following:UDP 16384-18538 - Cisco SPA303 - RTP "voice" portsTCP 5060-5080 - Cis...

add a new ephone to CME with web interface

Hi all,i would like to add new ephones (SPA504G) to our CU 560 with the web Interface. I've enabled auto-reg-ephone under telephony-service, but it doesen't work. There is a poup Message "No new phone to add".What can I do?ThanksRi...

Daylight saving time adjustment on BE3k

Hi Team,Does the CUCMBE3K support automatic adjustment of the time in accordance with daylight savings time. Or is this a manual process that have to be done?Thanks,Henry

Resolved! Cisco SPA500 Series IP Phones

Hello guys!Does all the Cisco SPA500 Series IP Phones can be managed by the UC540W-FXO-K9? Thanks in advanced!

UC540- Doubts about default features

I did a quote from local distributor, and they said to me that the UC540 didnt homologated to Brazil, so cant be sould here in Brazil, Is it true?Another question, I read the informations in the follow link, but i have some doubts If i understood cor...

SPA 502G Web interface

Hi I am junior admin and because we have 1 port /working place I need to configure that IP phone and pc are connected together. I configured VLANs, and port is configured as trunk. When I configure (via Phone settings) VLAN membership, phone is opera...

Is there query string I can use on a SPA phone to cause the phone to dial?

Hi all,I have build a web app where I can configure the IP address of the users phone and then have a bit of code that when I click a phone number it causes the users phone to dial that number. e.g. its a home made click to dial feature.This query st...

Ask the Expert: Cisco Smart CallConnector

With Shahryar Talukder Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to get expert insights and learn about the Cisco CallConnector suite with Cisco expert Shahryar Talukder. He will also explain how the C...

Voice Systems and Accessories - Small Business

Forum Posts

Resolved! UC540 - hunt group timeout resets

UC520 SSL VPN Full Client package installation failed

Unable To Get Admin Access To SPA508G

SPA9000 drops on hold call

UC560 - SF2010P smart ports

SPA504G choppy. But 7941's are not!

Can I duplicate phone button settings?

Cisco SPA303 -- Does not get any incoming calls, outgoing calls are also spotty

add a new ephone to CME with web interface

Daylight saving time adjustment on BE3k

Resolved! Cisco SPA500 Series IP Phones

UC540- Doubts about default features

SPA 502G Web interface

Is there query string I can use on a SPA phone to cause the phone to dial?

Ask the Expert: Cisco Smart CallConnector

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

7841 3PCC LDAP error connecting to server

SPA303 Call History, External or Internal.

UC560 CME toll fraud issue

SPA122 ATA Bells

Cisco 7970 won’t pull firmware, DHCP Request every 20 Seconds