Hello, in the next weeks here in our company we need to implement a remote location (teleworkers via vpn) and i've read TEL https://supportforums.cisco.com/docs/DOC-15031I want to use an SR520 on the remote location with phones behind it (on TEL it i...
Does anyone know how to connect a paging system to a FXO port on a UC540? Configuration? I know there is something to do with dial peers but I don't know what.
We are cutting over a new UC320W 2.3.2(6) and the phones keep freezing up. If I try to make a speaker phone call it takes 9+ seconds for the system to go off hook. We have rebooted the SG300-28P PoE (Version 1.2.7.76) and the UC320. When you reb...
All-So we have a client with a UC560 that is reporting that it is running out of disk space:"Feb 24 18:06:14 localhost platform_config: Critical amount of disk space used, please backup log files using the copy log command"Below is the result of a sh...
Hello, I have an issue with multisite using 2 UC520s, I have set it up using CCA for both Data and Voice which was straight forward, data seems to be working perfectly, while voice seems to be working only one way, meaning if I call from site 1 to...
I have recently installed a brand new UC560 with the latest software pack. The phone system is working flawlessly, however there is no music on hold. When a call is placed on hold there is just a faint ticking sound. I have made sure that the corr...
Hello,I have a UC320W uisng SIP trunks and I have an issue with my FAX number. I have configured a Fax user, assigned it the number and assigned the user to the FXS phone. Under call forwarding I have configured the "Call Forward Busy/No Answer" op...
I wanted to know when there will be multiple SIP trunks on the UC520 (command line or CCA -- don't care which)? I've seen a document http://www.cisco.com/en/US/docs/ios/voice/sip/configuration/guide/sip_cg-multi-registrars.htmlbut I don't think it w...
Hi,For a BACD, is there a way to change the Hunt Group Type to 'First Available' (Asterisk terminology)?The call flow is as follows:Call rings on receptions phone on a shared extension (301). If that is busy transfers to BACD (pilot 501).Members of t...
подскажите как решить следующие проблемы:1) как настроить маршрутизацию внешних вызовов (есть внешние номера n-шт входящие с которых нужно перенаправлять на определенные внутренние номера и наборот)2) провайдер подает на вход 7 знаков, а хочет получи...
When I call the number it rings once and then it will get busy signal there after on incoming calls
A VOIP provider uses a 74.122.242.0/24 network range for incoming and outgoing VOIP services.Their setup documents request that we allow the entire range.Typical of Cisco, the CCA only allows individual IP addresses to be entered.Can someone inform m...
Have a client with a UC540W with a 25MB/3MB Charter Internet connection. Flow: Internet - ASA5505 - UC540When directly connected to the switch which goes through the UC540W, they get regular 25MB download speeds.When connected to the wireless, the s...
When I try to enable my UC540 alternate greeting prompt it plays but then the regular prompt plays directly after it. I am using script v04.aef, when using v03.aef it doesn't even come on when enabled. Any suggestions?
Hi,I've setup a UC540 with 6x FXO lines using the addin VIC card. The 6x FXO lines have been split into 2 Trunk Groups.The client wants to be able to use 9 for dialing out on one group, and 0 for the other.I've setup the Outgoing Call Handling Prefer...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: