Hi all,I've a little issue with address book on UC320. I just loaded a CSV file into the external directory and I have 2 questions:1) Why only 100 slots? Is there any way to break this limit?2) From SPA502 phones the contacts are displayed not alphab...
This question has a bit of a broad scope, but I am a total newbie to VLANs despite being an IT consultant for 28 years now... The network was never my focus until now.Using the hardware in the subject line, can I propagate the Voice and Data VLANs al...
Hi Thre,We have a UC560 that the admin logon to the unit, through CCA and Telnet doesnt work for the CUE web interfae.How do I reset the CUE web interface admin password?ThanksGraeme
Hi, I've bought a SPA2102 yesterday, and I've upgraded it to the lastest available firmware version: 5.2.12.I've configured and tested it and everythings work fine, but I would like to know if there is the possibility to have 2 Voip account on only 1...
I got the spa9000 and spa400 with 2 pstn lines. how do i make line 1 roll over to line 2 when im on line one? like a call waiting sorta setup. Iv been reading around online and in the admin guide but im unable to find any info on it.
Hello,we are a service provider and our customers buy their ip phones from internet retailers, maybe used ones from ebay, but certanly not from us. We would like to use the SPC format so we can --target to the different mac (there are passwords).1. T...
hii'm using 2 SPA1001 SW 3.1.19 SE & HW 2.2.1(659e)calling between two units works fine within same network, yet no audi while making calls between same units across different networks/ISPiam new to this so apprecaite so advices on how to configure m...
Hi,I bought two SPA942 phones yesterday ( Second-hand ) but I can't restore my SPA942 phone without admin password .I don't have any, i tried lot admin/admin,**** ,1234 and more .any method to factory setting ? Please help me ...Thank you
WHAT?Today we are announcing the release of the Cisco UC320W 2.1.4(3) Limited Deployment Firmware release. This fix release is available only via the Cloud by installing the attached Platform Modification File (PMF). This is the 2.1.4(3) firmwar...
I wanna make a factory reset in my SPA301 any suggestion how to do that, thanks for your help.
Hi guys, I am trying to configure the UC320W with SPA300 and panasonic phone. I connected my laptop on LAN port 1 (to access the configuration page), SPA320W on LAN port 2, Panasonic phone on FXS port and PSTN line on FXO port 1. I was able to config...
Hi,I'm thinking this has been asked before however I'm unable to find any answer.Does anyone know how to configure SPA5xx/9xx IP phone to do Auto answer/Paging function ie for inbound call, phone will auto answer and go speaker mode ?On the User sect...
I am setting up a UC320 for small solution with centrex lines, these lines require to dial "9" after you select outgoing line, the system keeps giving errors (voice errors from provider), there is somethig wrong with the dial out plan. When line is s...
Is there a way to get back to the AA once a caller enters the voicemail of a dialed extension? A client of mine had the request so when callers reach a person who is not available they can get back to the AA and dial another extension.Thank you.-Tim
Our company uses a UC540W-BRI-K9 as a communications system with several SPA phones. The UC540 has software pack 8.1(planning to upgrade) and connected with ISDN lines. We configured it by CCA 3.0(1) and everything is working OK. The problem is th...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: