Hello, I have recently bought CISCO SPA504G, I am new to setting up ip phones so need your guidance in this. Q1: I am using sipgate basic for my ip phone, I need to enable MOH on the IP Phone, I just want the default CISCO Music to play but it re...
Hello, I have recently bought CISCO SPA504G, I am new to setting up ip phones so need your guidance in this. Q1: I am using sipgate basic for my ip phone, I need to enable MOH on the IP Phone, I just want the default CISCO Music to play but it re...
My hope is that in documenting events here in some detail, I may somehow find a solution. For many years, I ran a Billion 7401VGP partly as an ATA solution for phone calls. It was reasonably solid apart from the occasional echo but it has been retire...
Hi I have a Cisco SPA 112 that is connected to an analogue bell. The SPA 112 and bell are setup using STUN as an extension on a 3CX system. My issue is that there is a delay before it starts ringing, the bell is about 4-5 seconds later than the ph...
I purchased the SPA2102 a couple of days ago, and was able to go into the configuration and set up my VOIP. The phone is working now, but I need to go back into config to set up some other options. When I enter http://192.168.0.1 into my browser, i...
Under Management, User List for the SPA-112 there is a User Account with the User name "Cisco" that can't be edited, changed or removed. That user account has no password as far as I can tell. Attempts to change the name of that account, or the pas...
Hello, I have an SPA525G IP Phone Firmware: 7.5.6Hardware version: 1.0.0 People very often complain on the other side, that they can not understand me very well. So I did some tests. Increasing the handset input gain did help only a little bit. ...
Our Cisco Unified Communications 540 Voice & Data Solution for Small Business (UC540) is no longer supported as of Jan.2017, but I need some help. I recently ran a "Shields Up" port scan test www.grc.com & it shows port 443 as open & not "stealth". S...
Multiple phones spa504g 7.6.2b are losing registration many times per day.2 locations , 1 with 21 phones and 2nd with 35 phones both behind nat (dd wrt) registering to asterisk 13.17.1 on the external serverEach phone is configured to use deferent s...
Hi,I'm sorry about my English (I'm French). I have a problem when a try to send fax with a SPA112. The fax dials the number and the distant fax drops out but the carrier is not complete and the fax is not passed on. I have a return no answer, occupie...
Is there a way from the phone itself to check firmware version once you have done a factory reset (#123456789*0#)?We have purchased these used and they were locked ICL/ITL, I reset them using said method and now they are stuck in upgrade because the ...
Hello all,I'm having some issues provisioning Cisco Small Business Phones (SPA Series). The filenames requested from the TFTP server are not consistent, and I haven't been able to find this behaviour documented somewhere.The issue is some units reque...
Hi, I have a strange behavior on my cluster monitoring, from time to time I see the RTMT "Cisco Jabber Summary" counter graphics going to "zero" and coming back to normal values, this is not important but it seems to be that at the same time the LDAP...
SPA 303 and 504G SRTP issueHi,I have a problem that when SRTP mode is enabled on SPA 303 and 504G answer "488 not acceptable here" on incoming INVITE. SDP of incoming INVITE:v=0o=FreeSWITCH 1505106066 1505106067 IN IP4 38.108.164.66s=FreeSWITCHc=IN I...
I have an elderly customer who is having problems dialing out because the dial plan timer on her SPA112 is not long enough. I'm having difficulties increasing this.To try to fix this, I added a "P20" to the beginning of the Dial_Plan_1_ string.(P20|...
the pap2-na ask for password in the process of reset, after the 73738# and i need the password, plz help
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: