Hello,
Here is the situation: I got a analogue intercom system. The intercom needs to be hooked to the VOIP environnement. I cannot use an ATA as the Intercom system is the one sending the tone.
I bought a SPA 3102 and use the FXO port to connect t...
Hello,
We have two UC540 in Multisite mode.
Voice works fine and we could make calls between sites without problems.
The problem is that a user in site A could connect with a nasdata in site B, but speed is too low, no more than 700 Kb/s.
Wan port o...
Hi Friends,
I have configured SPA 508G Phone in my network and it's working fine, but I want to add *72*(Passowrd)*(Dialing Number) for international numbers.
But when I try to type this code, phone says "Invalid Number". How can I resolve this prob...
Hi guys, so I recently upgraded my phone's firmware from 7.1.7 to 7.6.2 and one thing I noticed right away is that the BLF keys I have assigned to the line keys alternates between the name/shortname and extension. The old firmware behavior was that i...
We just received our first BE6000S and when we plug in to the vga port fresh out the box it goes through its boot procedure and the last few items on the screen are blk1 - Hard Disk null with additional message info then blk2 Hard Disk null all the w...
Hi Gents,
I am use to working on CUCM 8.6 and above, from a WebConsole view.
I have a client that has a UC560, and I therefore being more use to the GUI, downloaded CCA 3.2 and have it installed.
I have a challenge on 2 things.
1. I have a us...
Team,
Looking for a way to do (Basically Toll Fraud) for a customer.
They are looking to dial into their UC560 and get prsented with dialtone to then make a call out of the UC560. I see MANY ways to prevent this but any way i try seems to not work....
Hi,
I have a spa232d and I have two VoIP phones. However when registering them, they both get the same IP. How do I hand each phone it's own IP, so that I can assign them each an own phone number. I'm using SPA-302D phones.
Hi,
I have a 4 ports router and all ports are used. One of them is connected to SPA122 blue port. I want to use the yellow (Ethernet) port as a 5th LAN switch port of the router and connect a printer to it. I set the ATA to bridge mode.
The problem...
Hello, My name is Dhaniels, I'm internet & Telephone Service Provider, And i made this because i'm having some problems with the provisioning on the Cisco Spa2102 ( I have a lot of this devices something like 300 Units), So, i don't know how to disab...
Dear all,
I have extra 20 SPA509G phones which previously provisioned by VoIP hosted provider and then changed to another. They have pushed firmware 7.6.1 to all phones al so they disabled web login info and activated admin password.for factory rese...
Hi,
I have a 4 ports router and all ports are used. One of them is connected to SPA122 blue port. I want to use the yellow (Ethernet) port as a 5th LAN switch port of the router and connect a printer to it. I set the ATA to bridge mode.
The problem...
Hello,
I am trying to configure a UC560 to automatically call forward all calls to an outside number only on off business hours.
The main DN is the pilot of a hunt group.
Can this be done? Could you please point me in the right direction?
Thanks!
UC540 - can't get smtp working to Office365 for voicemail
Migrated to Office365 and using smtp.office365.com for the external smtp server, port 587, correct credentials and getting unknown smtp host. I can get a telnet client, and powershell to both...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: