I am trying to set up an ATA 190 to use my Panasonic analogue phone via my router. I have followed the instructions but the phone line LED on the ATA doesn't light up unless I pick up the phone to try and find a dialling tone in which case the phone ...
Hi,I have a new sp3102 and configured it for use with 3CX pbx, all was going ok until I changed the 3102 admin web interface ip address.Now I cannot access the web interface? and it doesnt respond to a ping.Is it possible to reset to factory defaults...
Is it possible to have an extension automatically answer to speakerphone within a given time period?ie. A dentist is working on a patient and the receptionist would like to intercom to the dentist to provide patient related information, but the recep...
Hi GuysRequesting for your advise on this. We have Analog Trunks connected to the Voice Gateway 8300 Router and noted that the ANI from the PSTN keeps on changing on a per call basis to begin with and also its in improper format. Looks like the Carri...
I have many SPA 122's that I have discovered are rebooting at irregular intervals with reason code H0. I'm in a Metaswitch environment using the SIP Provisioning Server on the Meta. It seems H0 implies that the time stamp of the config that the SIP...
SPA122 ATA voice adapter, Version 1.3.0 (008_Customer_Test) I'm facing a problem, when I tried to upload the configuration file into ATA via TFTP with DHCP option 66, the box does not restart after loading the file. Device has the factory default pro...
Hi, Need help. We had a contract with Vodafone UK who supplied us with around 40 Cisco SPA525G devices, our contract is now over, they dont want the phones back. All the phones are locked to Vodafone config. Does anyone know how to unlock the devi...
Has anyone used the Cyberdata Door Intercom http://www.cyberdata.net/products/voip/digitalanalog/intercom/index.htmlwith a UC540 System? Also looking to use this to operate the door strike, does anyone have anything to offer on this?Thanks
Hello,I have a Cisco UC520, Cisco IP Phones (7911, 7941, 7931) and my switched network is done with Nortel BES 1010.I have configured two VLAN (voice and data), and a trunk between the UC520 and the Nortel Switch.I don't Know how to configure on the ...
My office has a SPA 508G which has the internal voice mail. I press the mail button and it goes to voice mail, I enter the pin and it says we have no new messages, no old messages and that the message notification is disabled. How do we enable it? We...
Hello,I'm using asterisk PBX and Cisco SPA8000. I'm unable to make outbound calls even when I have setup my trunk and outbound routes from the asterisk pbx. Is there a config in SPA 8800 that would stop this from working?
Hi Cisco TAC, It's my first time to use Cisco SPA8800. Is there a way I can ring my Phone1 from PSTN using Line1?
We've installed a Viking RC3 to handle remote door entry with the 540 product line. Right now the Viking answers and then waits for the Cisco to enter digits, but the Cisco has already sent them.. I need it to wait to send the digits to triger th...
Dear Community,I've tried changing the language of my SPA504G, putting the script I've found into the manuals.Unfortunately, something went wrong and now the phone's display is completely black. I did many rebooting, unplugging/re-plugging, but nothi...
We are currently running CUCM 12.5.1.16900-48. We have Cisco 8841 and 8845 model phones. When a call is made from outside our network the caller ID shows Wireless Caller and the phone number, but once the call is answered the phone number goes away...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: