Subject: Intermittent SSID Connectivity Issues – Cisco C9130AXI-E APsWe are currently experiencing an issue where some users are unable to connect to the SSID, while others who are already connected are being intermittently disconnected.The environme...
Saw this bug CSCwv38239 - Catalyst 9300X PoE ports fail to establish Ethernet link with Vaisala temperature sensors after upgrade to IOS XE 17.15.5. Is anyone seeing the same problem with Cisco Access points on these switches ? All works on...
Hi,I'm working on migrating our 3802i from a 5508 to 9800-CL. The joining of APs to the 9800-CL is working but I'm not able to rollback to the 5508 running 8.5.182.7, which I am practicing in case there is a need. When I point the 3802i back to the o...
In which version in wifi7 access point will support for 6GHz with indian Regulatory
Hi Cisco,We understand this is a cosmetic bug and doesn't impact service.However, we'd like to inquire about the roadmap for its resolution. Do you have an estimated timeframe for when a fix might be implemented?
Hello,I am new to the Cisco Self Standing Wireless LAN Controller System. I have always used Mobility Express, and I know it is end of life. The purpose of this AP is for learning and using it in my home lab. I have read this post below:Migrate ME to...
Hi all,I'm following the Cisco document "Configure 9800 WLC Lobby Ambassador with RADIUS and TACACS+" (Document ID 215552) to set up external authentication for Lobby Ambassador users on a Catalyst 9800.In the TACACS+ section, the ISE shell profile i...
After putting the 9163E in site survey mode with the CW-ANT-D1-NS-00 already appropriately attached, it will not broadcast anything. The show interfaces dot11radio 0 shows all zeros. Radio zero also keeps going down after a few minutes and then immed...
WLC 9800-CL17.17.1The management port of mt WLC is 192.168.1.201, and 192.168.1.197 is my RADIUS.I am trying to send CoA from 197 to 201, but I got no response from the WLC.1. able to ping 2. "show run | section aaa", I can see belowaaa server radiu...
WLC#sh ip int bInterface IP-Address OK? Method Status ProtocolGigabitEthernet0 10.0.15.210 YES manual up up WLC#ping 10.0.15.210Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.0.15.210, timeout is 2 seconds:.....Success rate is...
Looking for a sanity check on a possible FlexConnect scaling issue before making changes to our site tags.ENVIRONMENTWLC: Cisco Catalyst C9800-L-FSoftware: IOS XE 17.18.4aSingle WNCd384 APs across nine school buildings10 site tags, with 146 APs in th...
Scanners dropping out halfway down an aisle, vehicle terminals that freeze at the dock door, and a heatmap that looked fine on paper. These are the most common warehouse Wi-Fi complaints we see, and in most cases the access points aren't faulty. The ...
Hello Everyone,I need to generate a list of Access Points that are currently offline, along with their corresponding serial numbers, from a 9800-80 Wireless LAN Controller (WLC). However, I have noticed that the "Join Statistics" page on the 9800 WLC...
I have an internet gateway, with its own WiFi, running a DHCP server. I connected my MR57 to one of the ethernet ports and setup a 6GHz-only SSID in bridge mode. I connect my clients to the SSID and they get a DHCP address from the server on the gate...
We are migrating APs from our existing Cisco Catalyst 9800-CL WLC running IOS-XE 17.9.3 to a new Catalyst 9800-CL WLC running IOS-XE 17.12.3.Instead of moving all APs within a single maintenance window, we are performing the migration on a site-by-si...
