AP disconnect automatically and join again Showing trap disassociated previously due to ap crash ap mode 3800 why this problem face and how to resolve? please help me
Forum Posts
[*12/14/2022 06:23:05.5811] waiting for WCP to initialize[57C[*12/14/2022 06:23:05.5811] waiting for WCP to initialize[57C[*12/14/2022 06:23:05.5811] waiting for WCP to initialize[57C[*12/14/2022 06:23:05.5811] waiting for WCP to initialize[57C[*12/1...
Hello,I have a Cisco WAP571 AP with 2.4 Ghz band enabled, in 802.11b/g mode. Since a week ago, all clientes connected to it disassociate after some minutes and have to connect them again. It is located in a closed building with only one floor and no ...
Hello Experts,We have a client who is managing a community of villas and Apartments ( around 300 villas and 500 apartments) and its a big site including Outdoor areas.They have asked our suggestions to design WiFi and one of them seems very strange r...
Running 17.6.4 on 9800-402.7.0.356 patch 6 on ISEWhen I run "password encryption aes" on the WLC,ISE will not accept clients for DOT1x authentication. works fine before running the command. and after a "no password encryption aes" and reboot it works...
Hi all, I configured a WLAN on our Catalyst 9800 controller with MPSK. It works fine and can connect with one of the preshared keys. However, how do I know which key does the client uses? I don't need to see the entitry preshared key, only the priori...
Dears, We purchased Cisco Virtual Controller, and we don't know from where we can download the VM.Any guide,Kind Regards!
Hi there! Please, help.I have cisco wlc 5520 + windows radius nps with dynamic vlans assigment and it works fine.I bought cisco catalyst c9800-l and configure it by cisco guides with is using my working windows radius nps to got dynamic vlan assigmen...
Resolved! Wireless Survey Requirement
I want to conduct a wireless survey for cisco C9120AXI-E. Do I need a controller to accomplish the survey or I can just start the survey before deploying the controller, and if this is possible how should I do it? Thanks in advance
- FYI : https://www.cisco.com/c/en/us/support/docs/field-notices/704/fn70479.html >...A newly installed Access Point (AP) fails to join its controller or it joins the controller, but is only able to b...
is there a null zone when mounting the 2544 antenna and if so, is there an issue with mounting the antenna vertically with the dome facing up and or the dome facing down. from a height of 30 feet.this is in reference to null zone charadteristics to t...
- FYI : https://www.cisco.com/c/en/us/support/docs/wireless/aironet-700-series-access-points/218447-ios-ap-image-download-fails-due-to-expir.html https://www.cisco.com/c/en/us/support/docs/field-notices/725/fn72524.html M.
Resolved! 9800 show APs with zero clients
Hi all.during AireOS days, we can see all APs with the number of clients connected.Nowadays that doesn't seem to be possible...in the Monitoring / Wireless / Clients - only shows where do I have clients, this is not the intentionin the Configuration ...
Hi Community,I can't login to my controler wlc9800,How I can disable this config from CLI. Best regards.
Resolved! cisco 1815
hello I am facing an issue with 1815 AP cant join the controller AP primary and boot image 17.10.0.181 (before updated to ewc image)backup image 8.10.181.0 I do convert from ewc to capwap and try to join the controller but its not join also i tried t...
