Hi everyone We have set up Cisco ISE Guest management in the lab. We are using Cisco ISE v3.1 and Mobility Express for WiFi.Guest processes are completed successfully. Then msn.com opens on a new page! This problem is not relevant to ISE or EndUser. ...
Forum Posts
Resolved! C-ANT9103 with C9130e
Can I use this antenna with 5GHz?Is 802.3bt required?I want to install it for a warehouse at one end, replacing ANT2566P4W-RS= I have RF devices 1x1 stream Please, I would appreciate your answer
Hi everyone, I'm currently facing an issue with the Embedded Wireless Controller (EWC) running on Catalyst 9115AX Access Points. We're using MAC filtering across all WLANs (SSIDs) to control access to the wireless network. Each device’s MAC address (...
hello everyonethese days i am experiencing a problem due to Redirect ACL failure message,below i am releasing the details of my EWLCEWLC firmware 17.6.4I checked via wireshark the response received from cisco ise and indeed the connection is accepted...
Hello, I tried to launch a job on my Cisco Prime (current version is 3.8.1) to archive the configuration of my Cisco 9800 WLC, but the job gave me the "Partial Success status". Either the Running and the startup configs are successful, but the "Fetch...
Resolved! C9800-L-C-K9 無線コントローラのポート設定について
こんにちわ。 C9800-L-C-K9無線コントローラにおいて、 ファイアウォールのようなポート設定ってあるのでしょうか？ 例えばコントローラ上でTCP80を開放したいんです。 となった場合の設定方法を教えてください！！ ドキュメントやGUIの設定画面を探してもどうしてもわからなくて。 よろしくお願いいたします。（そもそも無線でポート遮断という概念があるのか？）
Customer had some update done on Aeroscout and since then NMSP is inactive Controllers: 2 5508 in HA mode running 8.5.140 MSE 3355 running 8.0 Prime version 3.4 Verified the Auth list. readded the Hask Key shown in MSE. in the debug it shows handsha...
I need to know what the access points' joining procedures are in SSO deployments and N+1 deployments, and what the timers are in each section. For example, in SSO, if the primary controller fails, what will happen with the access point, and if it com...
Hi team, we have installed c9800 HA pair 2 months ago, running 17.12.4 version. We are facing now random reloads of standby WLC every few hours with this info: Reload History: Reload Code: ReloadReload Description: Reload Command - RIF: Bulk Sync, sy...
Resolved! Cisco ISE authorization
Hi Experts, I have setup where Clients connected on WLC-9800 SSID should get Vlans assignment from Cisco ISE authorization Profile, But it still clients gets IP from Access Policy configured on WLC-9800AAA is configured on WLC with Mac Filtering and ...
Is it possible to create a client exclusion policy for the Cisco 9800's to prevent bad password attempts from locking out a users AD account? I have found some documentation that all seems to be for AireOS for configuring Client Exclusion Policies wh...
My AP is in u-boot mode. I need a .bin file executable from this mode to boot it in Mobility Express mode. Per esempio ap1g6-k9w8-mx.153-3.JF12.bin. Where can I download it?
Hi,I have a working vWLC with 5 APs and all of them are in one VLAN and SSID.Now I want to add another SSID and VLAN. I changed the switch ports that connect to APs from access to trunk with native VLAN that is previous access VLAN. I created another...
Hello,The master aironet 1832 from our network crashed between wednesday and friday.I did a backup of its config, so I have a config.txt file up to date.As we need to have the master for some production usages (I don't know why, a laptop or a smartph...
お世話になっております。以下の脆弱性について影響を受けているか確認しているのですが、https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-wlc-file-uplpd-rHZG9UfCWLC#show running-config | include ap upgradeWLC#コマンド結果は上記の通り、何も表示されず影響を受けていないものと判断したのですが、#show ap ...
