active stays up, stby keeps rebooting Initializing Hardware ...System integrity status: 90170200 12030107System Bootstrap, Version 16.10(2r), RELEASE SOFTWARECopyright (c) 1994-2018 by cisco Systems, Inc.Current image running: Boot ROM0Last reset cau...
Forum Posts
I am trying to deploy a 2802e AP in my home network...it currently on my network, has an IP address and is pingable. The AP is running 8.5.0 Mobility Express code.....however when it boots up the CiscoAirProvision AP does not show up in my list of AP...
I am installing the 2802i APs in mobility express. However, the AP is not broadcasting the SSID. Attached are the running configs of the device. Any help will be appreciated.
Resolved! 9800L WLC Vrs 9800 Embedded WLC
Hello Everybody, I'm going to buy a Cisco Wireless solution we are going to have 10 access points 9130 and 9800L WLC, but we can go by using the embedded WLC in 9130 access points instead of 9880l WLC, what i need to know the pros and cons between 98...
Resolved! Acess point syslog server configuration
Dears, I have WISM 2 and try to configuring the syslog server for Access points with the below command. config ap syslog host global syslog_server_IP_address But i found all APs communicate directly with syslog server & creates syslog host for each...
WLC#chassis redundancy ha-interface local-ip 192.168.0.2 255.255.255.0 rWLC#$-interface local-ip 192.168.0.2 255.255.255.0 remote-ip 192.168.0.1WARNING: Changing the chassis HA interface IP address may result in a configuration change for th...
What is the reason for the client delete in the debug below on a WLC 9800? Deleting the client, reason: 135, CO_CLIENT_DELETE_REASON_MN_AP_AUTH_STOP, Client state S_CO_L2_AUTH_IN_PROGRESS Thanks
We have cisco 5520 wireless controller connect to 88 Aps, Suddenly in the morning some of the clients got connected and some of them get connected but says no internet.connected clients are both 2.4 and 5GHZ clients. Please advice
I am upgrading 2 5520 controllers HA, and 2 Guest Anchors to 2 9800L's in HA and 2 9800 Guest Anchors. We have a 3502's and 3800's in environment now. Upgrading to 9130's I am looking for the best way to upgrade and have them possibly run in parall...
Hi everyone, I have couple of Wireless Access point:model: AIR-AP1852I-I-K9boot image: 8.10.142.0 and also tried 8.5.140.0I made a factory reset to the access point, and reconfigured it, then created an SSID but it never broadcast it. the AP was joi...
Hi Wireless folks,I'm playing around with a C9800 and I'm wondering where the CoPP configuration and documentation is. I bet the box does some CoPP out-of-the box and I want to understand how it works and whether it can be tuned.For example, I'm wond...
Hi everyone, I've got a simple question. Existing wireless infrastructure (AirOS or IOS-XE) and I need to lifecycle my APs. Is it possible, to use DNAC PnP, to assign hostname, primary and secondary controller, AP-Group/Tags to an AP without the need...
Resolved! Mapping Specific SSID to multiple Vlans
Hello Dears,If we have a core switch with multiple subnets for the same SSID , on local mode this would be fixed via interface group , however i faced a situation in a Flexconnect environment where for SSID X is multiple small subnets configured on t...
Hi Anyone can explain the DHCP override in the below picture. Thank you
I am using my AP in EWC mode. I am using Windows 2019 NPS as the AAA authority. I have set up admin (web & ssh) access and have set up 802.1x for one of my WLANs and it is working as expected. I would like to have a few WLANs that are restricted b...
