Hi Guys, I have Access Points 1552 in Mesh Network, 5 GHz for the Mesh Backhaul and serving clients on 2.4 GHz I am wondering why I am not getting any Cleanair nor in the GUI nor in CLI show {802.11a | 802.11b} clean air device ap Cisco_AP any th...
Forum Posts
Can some help me that mobile client disconnecting from WLC they should re login, I downgraded IOS from 8.5 - 8.3 from but still same problem. I am coping the log.
Resolved! flexconnect configuration: two options
for flexconnect its possible two ways for configuration: 1) without "vlan support" and, port where access point is connected, in access mode with this configuration obviously there are less settings and time for config 2) access point is in flexc...
Hi All,We have upgraded our controllers to version 7.6.100. After upgrading, the access points also upgraded their version to 15.2(4)JB3. But, the problem is that after this process the APs do not get IP. It stays on this state:*Sep 26 03:55:36.334: ...
Greetings! Is there an posibility to connect external third-party 3G modem via USB to ISR 891 router? I try to connect MTS 3G-CDMA450 modem (produced in Ukraine)
Hello, my access points are all at TX Power on Global. I can see that many only stand on TX Power Level 5. However, this is not enough to expose the WLAN far enough. If I manually set the access points to Power Level 1 or 2, my wireless network is ...
hello ; I have a cisco Router Cisco 886VA , I can't fin the AP on the Router . can some one help me to configure wlan on the Router . Thank's.
Hi I need to know if i use Aironet Access Point AIR-AP1832I-E-K9 as AP controller can i use AIR-CAP3602i-A-K9 V01 as AP , will both of this device will be compatible to each other so i can control all AIR-CAP3602i-A-K9 V01 from one Aironet Access ...
Resolved! Upgrade IOS for a 3802i with USB Key
Hello, I have a question regarding the 3802i Cisco Aironet. Indeed, there is a usb port behind the AP and my question is the following one : It's possible to upgrade the IOS of the 3802i Cisco Aironet thanks to a USB Key ? Thanks in advance f...
HelloI inadvertently 'ugpraded' an Aironet 1231 to an Lightweight image, and need to download it back to autonomous.Documentation on CC says to press the RESET button whilst booting until the middle light glows red - after that, the AP will set its I...
Resolved! Upgrade WLC 2504
I got in my environment 100 WLC 2504, all of them are in code 7.6.120.0 I would like to upgrade them to 8-5-131-0 any one could help me to find the upgrade path to which version I have to jump first? Thanks
My company is allowing me to move from autonomous access points to a controller-based wireless network. We are currently set as a giant hub-and-spoke model with over 200 branch locations all on their own subnet sending data traffic back to our corpor...
Hi I have want to install active and standby Wireless controller by using Cisco WLC 5520. Do I need to buy licences only for one controller ? or separate licences for both active and standby? BR
Resolved! WLC 5520 as Guest Anchor WLC
Hello, I want to build a secure access for wired and wireless guest. Currently, there are already two 5520 controllers (50 AP licenses) in HA mode (SSO) as well as an ISE for authentication of employees clients. I want to use two 5520 Controllers (in...
We recently had to upgrade our 5520 to 8.2.170.0 from 8.1.131.0To speed up the process, I had pre-downloaded the new image to all APs (a mix of 3502i & 3702i). So we rebooted the controller, and after it completed the boot process, all the 3702 APs j...
