HejI am trying to configure a class-map for BNG ipsubscriber policy. I am trying the below. If I press anything at all including ? after 2nd command it gives the below message and puts me back to top of config. Not sure how to create the class map, ...
Forum Posts
I get an issue when trying to assign bandwidth to a policy-map for DSCP bandwidth.Config:!ipv4 access-list ACL_GOLD10 permit ipv4 any any dscp af23!class-map match-all CM_GOLD match access-group ACL_GOLD end-class-map! Error:!! SEMANTIC ERRORS: This ...
HejWe are testing an IP subscriber BNG setup. And we were wondering if it is possible to assign subscribers to different VRFs based on username that terminate on same subscriber sub-interface.I tried to find some documentation on this, but couldn't f...
Resolved! l2vpn xconnect is not coming up
Hi all,My P2P l2vpn xconnect is not coming up. I trying to figure the problem out. What am I missing? hostname XR1interface Loopback0ipv4 address 192.168.100.2 255.255.255.255!interface GigabitEthernet0/0/0/0ipv4 address 10.0.200.6 255.255.255.252!in...
Dear all,I am looking at an odd issue where aaa is not working for a new XR node, but works for similar nodes.ISE logs clearly show user authenticated and authorised, but actual node does not allow access: sshd[54464]: Permission denied for <unknown...
HiWe’ve got an issue with a 100-Gig line card in our ASR 9006. It was working fine but suddenly went down.We tried moving it to another ASR 9006 chassis, but it’s stuck in the BRINGDOWN state. Here are the logs we’re seeing : can you tell what might ...
PID : N540-24Z8Q2C-M IOS-XR : 7.8.2 I want to know about smart licenses. The command is enable, but when I apply the command below, it behaves as if the license is off. RP/0/RP0/CPU0:PE-02#show run | inc licWed Mar 27 10:13:34.359 KSTBuilding confi...
Hi Does anyone know of a tool to convert a IOS XE configuration to IOS XR? Warm RegardsFrancois
HelloSome time ago, I used to use a cisco tool in which I could submit the source IOS configuration in order to have a target IOS XR config Do you know what is the name and the link of this toolThanks for your support
Resolved! A99-4HG : tengig ports doesn't show up
Hello, I'm trying to connect a A99-4HG-FLEX line card to ASR9910. Only four 100G ports are available, anyone knows how to enable the remaining 40 tengig ports ? RP/0/RSP0/CPU0:lab#sh int desc Interface Status Protocol Description-------------------...
Hi guys, Should be quick for you - trying to find the way to clear statistics in command sh l2vpn xconnect interface Te0/x/x/x.3531 detail ... Statistics: packets: received 653391833, sent 1016 bytes: received 179842397573, sent 472452 in 650...
Hi All, I am trying to boot up an IOS XRv 9k 7.4.2 in eve-ng but its not booting, it rebooted in the first 2-3 minutes and afterwards its doing nothing, i can see the following message on the console but its not progressing any further. any idea pl...
We have a client on our asr 9K router that we are providing layer 2 transport for to several sites. The client has asked us to also provide data center space for a remote server in our data center. Is there a way i can pop off the customers vlan on ...
I also posted this query in Cisco Community > Technology and Support > Networking > Routing but thinkit might be better here under XR OS specific questions. I have a query on which statement is true regarding using hsrp group id's >255 in the doc"IP ...
Hi guys! I'm having an strange behaviour. When executing a py that gets som outputs from iosXR devices, som of them works fine and some other devices (configured on the same testbed) are faling with the following error:The above exception was the dir...
