Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
ajayku2
‎06-12-2018
Enthusiast
Recent Badges
Awards
Recent Badges
See all
100 Helpful Vote
15 Accepted Solution
1 Accepted Solution
5 Accepted Solution
30 Helpful Vote
10 Helpful Vote
1 Helpful Vote
50 Replies
20 Replies
10 Replies
Stats
Member since ‎08-17-2011
258
Posts
104
Helpful
40
Solutions
Certifications
Cisco Certified Network Professional Data Center (CCNP Data Center)
Cisco Certified Network Associate Data Center (CCNA Data Center)
Cisco Certified Network Associate Routing and Switching (CCNA Routing and Switching)

ACE - x-forwarded-for equivalent for other protocols than HTTP

Created by in Application Networking
09-20-2013
09-20-2013
Hi, Sorry but this is not feasible with ACE. It can be controlled at software level itself but I am ...

ACE FT multi-context bridged VLANs

Created by in Application Networking
09-20-2013
09-20-2013
Hi, Do I configure the peer and group information on the Admin context or the individual context ? T...

ACE - x-forwarded-for equivalent for other protocols than HTTP

Created by in Application Networking
09-20-2013
09-20-2013
Hi, it is designed specifically for HTTP. ACE cannot insert the same to any other protocol. Even if ...

Re: How to configure ACE bypass traffic from Servers to Internet

Created by in Application Networking
09-19-2013
09-19-2013
Hi, Please refer the following link : https://supportforums.cisco.com/thread/132052You just need ser...

Issues With ACE 4710 Config

Created by in Application Networking
09-19-2013
09-19-2013
Hi, Ideally you should allow the traffic from inside to outside. Also try to use server NAT as used ...

Cisco ACE 4710 - Question

Created by in Application Networking
09-18-2013
09-18-2013
Hi, You can use source NAT on ACE. That way you dont have to point the default gateway to ACE. The l...

Clean Access Agent in Windows 8, 64 bit

Created by in Application Networking
09-18-2013
09-18-2013
Hi Ken, it should be downloaded by School's network administrator. This is suppose to be installed i...

Clean Access Agent in Windows 8, 64 bit

Created by in Application Networking
09-16-2013
09-16-2013
Hi Ken, You should post this question on Security forum. I searched a bit and found the following : ...

ACE20 - only loadbalancing to one real server

Created by in Application Networking
09-16-2013
09-16-2013
Hi, If you are behind a firewall or a proxy then chances are that clients are coming with a single s...

ACE20 - only loadbalancing to one real server

Created by in Application Networking
09-15-2013
09-15-2013
Hi, Few possible reasons are below : The probes are failing for other servers from other load balanc...

Problem with Upload PEM certificate

Created by in Application Networking
09-15-2013
09-15-2013
Hi Rodrigo, It is possible that the key is encrypted with a password. Please follow the steps as des...

IPv6 to IPV4 on ACE

Created by in Application Networking
07-30-2013
07-30-2013
Hi Ajay, Please refer the following link : http://www.cisco.com/en/US/prod/collateral/contnetw/ps571...

Load balancing imbalance in ACE

Created by in Application Networking
07-30-2013
07-30-2013
Hi Shobith, "persistence-rebalance strict" is the one which will help fix the issue. Configuring Per...

Re: IPv6 to IPv4 translation

Created by in Application Networking
07-26-2013
07-26-2013
Hi, I see you are willing to capture ipv6. You can create ACL using ipv6 : ace-4710-1/Admin(config)#...

Re: IPv6 to IPv4 translation

Created by in Application Networking
07-26-2013
07-26-2013
Hi, if you just want to verify whether the traffic is hitting ACE or not you can try the following :...
Public Statistics
Date Registered ‎08-17-2011 03:52 AM
Date Last Visited ‎06-12-2018 05:59 PM
Total Messages Posted 258
Total Helpful Votes Received 104
Helpful Votes Given To
See all >
Helpful Votes From
See all >