Activity in Technology and Support
Can we use POE extender if Meraki AP is connected from swich
Can we use POE extender if Meraki AP is connected from swich more than 100 meterplease suggest
Resolved! Relocating one of the fabric interconnect 6200 without downtime
I am trying to relocate one of the Chassis(2) and subordinate FI to different rack in same location without downtime. ENVIRONMENT: FI model: 6200 (EOS) Chassis Model: UCSB-5108-AC2 2 FI's connected to 2 chassis (blade servers) with high availability ...
Resolved! ap2802i cli ap-type cmd have no mobility-express option ?
hi, I want to convert ap2802i to ME mode. Community docs sad you can just use `ap-type mobility-express tftp://[]`But after I use archive cmd upgrade the new firmware, I find there is no ME option. I type ap-type ?, and it prompt only 2 options: 'ca...
c9300 stack ports down
New switches are stacked together. but why ports are down. same model c9300, ios version and license. Anyone has experience on this? Thanks
Cisco Aironet 2800i not broadcasting SSID on initial configuration.
Hello, everyone.I am currently running this setup:Cisco AIR-AP2802I-B-K9 802.11ac Access Point running Mobility Express version 8.10.196.0 from Cisco's websiteAIR-PWRINJ6= (802.3at)connected between Access Point and my laptop(for GUI access) via Cat5...
Cisco 3850 To Fortigate 60E OSPF Connection Via EtherChannel
Hi,I am trying to set up a connection via OSPF between my Cisco 3850 layer 3 switch and my FortiGate 60E firewall throw OSPF, but it's not working, has anyone done it before. I pasted my configuration below, note if you see misconfiguration it is jus...
Resolved! ap-type mobility-express tftp://<ip-addr>/<file-name> not working
I am trying to upgrade my Cisco Aironet AIR-AP2802i-B-K9 (v01) from LWAP to Mobility Express but somehow the command 'ap-type mobility-express tftp://<ip-addr>/<file-name>' does not seem to work although it works with other 2802i APs I have(they are ...
Redistributing from OSPFv3 into EIGRP with a distribute-list
I was working on a lab to redistribute routes from OSPFv3 into EIGRP.First part of the lab required redistributing all OSPFv3 IPv4 routes into EIGRP. The commands below worked.router eigrp CISCO address-family ipv4 unicast autonomous-system 100 ...
Resolved! Ios update for 3560-C : WS-C3560CG-8PC-S
HiI plan to buy WS-C3560CG-8PC-S (Catalyst 3560-C) for my home lab. I just created a new account on cisco.com (I did not register any equipment or contract for that new account). I was able to download ios 12 and 15 for that switch.- Will I be able t...
Clients does not connect to appropriate AP and connection is low
Hello All,Iam facing a strange issue from last 1 month.I have Wireless network running with WLC2504 and AP AIR-1832IScenario is I have AP in 1st floor corridor and another AP in ground floor area.We have one conference room near first floor corridor ...
Resolved! Cisco 2960X stuck in RomMode Can't flash IOS
Hi, Peeps,I have a Cisco Catalyst 2960X and early today I upgraded the firmware, upon reloading, the switch did not boot anymore, I tried the following workarounds:1. Pressing the Mode Button for 15 secs2. Power cycling the switch3. Trying to do the ...
Multi-auth and unmanaged switch
Hi,I have several devices on unmanaged switch that I need to authenticate via MAB. Unmanaged and upstream switch are connected via access port.My idea is to configure MAB on a access port of upstream switch, and use multi-auth host-mode.Would this wo...
Cant get Cisco C11111 to communicate with my ISP - old 5506X works
HiI am current running a 5506X firewall connected to my ISP.I get a Static permanent IP from my ISP which is locked to the mac adress.I am trying to upgrade to a C1111 instread of the 5506X and the C1111 has been set up with the same mac as the 550...
Multiple VMs and IEEE 802.1X multi-auth host-mode
Hello,I am doing a lab with a Windows host that runs VMWare WorkStation and has 3 Linux hosts as VMs. I have configured the switchport on the Cisco device that I am using (C112X) as the following:Note that MAB is enabled for 1 of the VMs that is not ...
Resolved! New to Devnet Sandbox, Anyconnect fails to connect
Hello, Im new to accessing the Devnet sandbox and happy to do it. I have Anyconnect on my personal laptop, and have entered the VPN address and credentials handed to me by the deployed lab, but I continue to get this error"the remote connection was n...
| User | Helpful Count |
|---|---|
| 76 | |
| 60 | |
| 46 | |
| 46 | |
| 44 |
