关于2504的FT（Fast Transition）的设置，版本8.3.141无法设置问题

[iliaodong]

如题：
通过WEB和终端设置都无法设置，提示信息见图，各位大神可以帮我看下是什么问题吗：

我的WLANID是1－16之间，还是提示必须1－16
另FT AKM在WEB下哪位位置设置可以告知下不？
谢谢~~

[Rps-Cheers · Accepted solution]

您应该没有选择 FT 802.1X或FT PSK，所以会出现图1的报错。

这里应该恢复了adaptive的配置，在CLI的配置的时候出现：


该命令后面应该只能跟WLAN ID，这里写802.11r所以报错。

正常情况配置，应该可以通过开启FT 802.1x或802.1x PSK,然后开启FT，这样应该OK。
Configuring 802.11r Fast Transition (CLI)

Procedure

---

Step 1	To enable or disable 802.11r fast transition parameters, use the config wlan security ft {enable | disable} wlan-id command.
Step 2	To enable or disable 802.11r fast transition parameters over a distributed system, use the config wlan security ft over-the-ds {enable | disable} wlan-id command. The Client devices normally prefer fast transition over-the-ds if the capability is advertised in the WLAN. To force a client to perform fast transition over-the-air, disable fast transition over-the-ds.
Step 3	To enable or disable the authentication key management for fast transition using preshared keys (PSK), use the config wlan security wpa akm ft psk {enable | disable} wlan-id command. By default, the authentication key management using PSK is disabled.
Step 4	To enable or disable authentication key management for adaptive using PSK, use the config wlan security wpa akm psk {enable | disable} wlan-id command.
Step 5	To enable or disable authentication key management for fast transition using 802.1X, use the config wlan security wpa akm ft-802.1X {enable | disable} wlan-id command. By default, authentication key management using 802.1X is enabled.
Step 6	To enable or disable authentication key management for adaptive using 802.1x, use the config wlan security wpa akm 802.1x {enable | disable} wlan-id command. Note When Fast Transition adaptive is enabled, you can use only 802.1X and PSK AKM.
Step 7	To enable or disable 802.11r fast transition reassociation timeout, use the config wlan security ft reassociation-timeout timeout-in-seconds wlan-id command. The valid range is 1 to 100 seconds. The default value of reassociation timeout is 20 seconds.
Step 8	To view the fast transition configuration on a WLAN, use the show wlan wlan-id command.
Step 9	To view the fast transition configuration on a client, use the show client detail client-mac command. Note This command is relevant only for a connected or connecting client station (STA).
Step 10	To enable or disable debugging of fast transition events, use the debug ft events {enable | disable} command.

[iliaodong]

1540488497lcj 发表于 2020-3-15 17:05
您应该没有选择 FT 802.1X或FT PSK，所以会出现图1的报错。
这里应该恢复了adaptive的配置，在CLI的配置 ...

web界面的时候要选择FT PSK（使用密码）或者FT 802.1X（认证登录），cli没有测试，刚设置好，已经成功了，谢谢

[fortune]

已经解决了啊，可以可以

[iliaodong]

vsop5207 发表于 2020-3-16 21:48
已经解决了啊，可以可以

请看沙发~~802.11r只合适苹果和三星手机，笔记本电脑上的无线网卡无法连接