各位大神, 昨天升级一台WLC2504的控制器系统, 初始版本是7.6.100的版本, 我升级到8.0.110启动正常的, 是从新版本8.0.110启动的, 然后我再升级到8.2.141启动后就不能从8.2.141启动, 控制器会在提示加载完8.2.141系统后重新从8.0.110启动,然后进入系统后还是8.0.110。 然后我再次升级系统更换了8.3.122的版本, 这次升级完提示重启后在加载完8.3.122的版本后就会停留在lunching这里不会再有任何进展了。 然后我用论坛上提供的RTOS把系统恢复到7.0.250后(
http://bbs.csc-china.com.cn/forum.php?mod=viewthread&tid=40460 (AS_5500_cavium_main-7.0.250.0) and RTO file corrupted (AS_5500_RTOS-7.0.250.0).), 再次尝试升级7.6.110再8.0.110再到8.2以上系统然后还是一样的效果8.2及以上系统都不能启动。 所有升级AES软件我都用md5校验和官网提供的md5一致,文件是没问题的。
和下面这个帖子里遇到的状况是一样的。
https://supportforums.cisco.com/t5/other-wireless-mobility-subjects/wlc-2504-fails-to-load-the-latest-image-8-3-120-0/m-p/2985878下面是升级日志:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.0.110.0 #### 从7.6.100升级到8.0.110启动正常的Bootloader Version............................... 1.0.20 #### FUS也是1.9 排除 CSCuu46671 这个bugField Recovery Image Version..................... 7.6.101.1Firmware Version................................. PIC 20.0Build Type....................................... DATA + WPS
System Name...................................... Cisco_be:40:64
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.1.31
IPv6 Address..................................... ::
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 22 mins 13 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... CN - China
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +44 C
External Temperature............................. +47 C
Fan Status....................................... 4200 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 68:9C:E2:BE:40:60
Maximum number of APs supported.................. 75
System Nas-Id.................................... Cisco_be:40:64
WLC MIC Certificate Types........................ SHA1/SHA2
(Cisco Controller) >Restarting system.
WLCNG Boot Loader Version 1.0.20 (Built on Jan 14 2014 at 11:40:45 by cisco)
Board Revision 0.0 (SN: Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate)
CPU Cores: 4
DRAM: 1024 MB
Flash: 32 MB
Clearing DRAM........ done
Network: octeth0', octeth1, octeth2, octeth3
' - Active interface
E - Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
- Model: 1GB CompactFlash Card Firm: CF B61FK Ser#: @771100001A1Yq7EMCKR
- Type: Hard Disk
- Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
Press
now to access the Boot Menu...
Loading primary image (8.3.122.0) #####从8.0.110升级到8.3.122 重启后提示加载了系统, 但没有从这个版本启动起来
100%
35904881 bytes read
Launching...
Launching images...
init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary
starting pid 688, tty '': '/etc/init.d/rcS'
Detecting Hardware ...
Installing ether-pow driver - 0x6008
starting pid 873, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar'
Setting up ZVM
Exporting LD_LIBRARY_PATH
Decompressing...
Validating...... OK
Cryptographic library self-test....passed!
XML config selected
Validating XML configuration
octeon_device_init: found 1 DPs
/dev/fpga: No such device or address
readCPUConfigData: cardid 0x6060001
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.
Cisco AireOS Version 8.0.110.0 #### 系统并没有从8.3.122启动, 而是从备用系统8.0.110启动了, 这里也没有提示任何错误信息
Firmware Version PIC 20.0
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Network Services: ok
Initializing Licensing Services:
License daemon start initialization.....
ok
License daemon running.....
Starting Statistics Service: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fastpath Hardware Acceleration: ok
Starting Fastpath Console redirect : ok
Starting Fastpath DP Heartbeat : ok
Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok
Fastpath CPU0.00: Initializing last packet received queue. Num of cores(2)
Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040
Fastpath CPU0.00: Core 0 Initialization: ok
Fastpath CPU0.00: Initializing Timer...
Fastpath CPU0.00: Initializing Timer...done.
Fastpath CPU0.00: Initializing Timer...
Fastpath CPU0.00: Initializing NBAR AGING Timer...done.
Fastpath CPU0.01: Core 1 Initialization: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting Management Frame Protection: ok
Starting DNS Services: ok
Starting Licensing Services: ok
Starting Redundancy: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting Capwap Ping Component: ok
Starting AVC Services: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting RF Profiles: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services: ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server: enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting RRC Services: ok
Starting SXP Services: ok
Starting Alarm Services: ok
Starting FMC HS: ok
Starting IPv6 Services: ok
Starting Config Sync Manager : ok
Starting Hotspot Services: ok
Starting Portal Server Services: ok
Starting mDNS Services: ok
Starting Management Services:
Web Server: CLI: Secure Web: ok
(Cisco Controller)
Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)
User: cisco
Password:*********
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.0.110.0 ### 启动后显示的版本
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 20.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_be:40:64
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.1.31
IPv6 Address..................................... ::
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 2 mins 34 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... CN - China
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +43 C
External Temperature............................. +46 C
Fan Status....................................... 4200 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 68:9C:E2:BE:40:60
Maximum number of APs supported.................. 75
System Nas-Id.................................... Cisco_be:40:64
WLC MIC Certificate Types........................ SHA1/SHA2
(Cisco Controller) >
(Cisco Controller) >show boot
Primary Boot Image............................... 8.3.122.0 (default) #### 启动项里显示的8.3.122为主启动设备, 这个启动选项我切换过几次都是不能从8.3启动。
Backup Boot Image................................ 8.0.110.0 (active)
有没有人遇到过这种情况呢? 有没什么办法可以尝试呢?