Hi Team,
I encountered a problem today with Cisco ASR1009-X Chassis, Cisco ASR1009-X (RP3) processor (revision RP3) IOS-XE Version 16.8.1.. The goeal is upgraded it, but navigate on official link the first step to upgrade a the latest suggest relese IOS-XE is upgrade ROMMON https://www.cisco.com/c/en/us/td/docs/routers/asr1000/rommon/asr1000-rommon-upg-guide.html#concept_zdm_2nx_5bb.
I Try to do it in small step with some problem.
- AS-IS 16.3(2r) Firmware Version ROMMON TO BE 16.9(4r) Firmware Version ROMMON failed
- AS-IS 16.3(2r) Firmware Version ROMMON 16.12(8r) Firmware Version ROMMON failed
- AS-IS 16.3(2r) Firmware Version ROMMON TO BE Latest Release no completed all module
First two point I received this error
Upgrade rom-monitor on Embedded-Service-Processor 0
Upgrade rom-monitor on Embedded-Service-Processor 1
% Error connecting to ESP 1
Upgrade rom-monitor on SPA-Inter-Processor 0
Target copying rom-monitor image file
rsync: change_dir "/rommon/mcp/CC/ELC_100G" (in rommon_upgrade_pub) failed: No such file or directory (2)
rsync error: some files/attrs were not transferred (see previous errors) (code 23) at ../rsync-3.1.2/main.c(1650) [Receiver=3.1.2]
rsync: read error: Connection reset by peer (104)
Upgrade rom-monitor on SPA-Inter-Processor 1
Target copying rom-monitor image file
rsync: change_dir "/rommon/mcp/CC/ELC_100G" (in rommon_upgrade_pub) failed: No such file or directory (2)
rsync error: some files/attrs were not transferred (see previous errors) (code 23) at ../rsync-3.1.2/main.c(1650) [Receiver=3.1.2]
rsync: read error: Connection reset by peer (104)
So not completed.
The latest step the upgrade completed but with some mismatch version, below output.
RT-AL-INTERNET#sh platform
Chassis type: ASR1009-X
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1000-MIP100 ok 01:01:00
0/0 EPA-18X1GE ok 00:58:37
0/1 EPA-10X10GE ok 00:58:24
1 ASR1000-MIP100 ok 01:01:00
1/0 EPA-18X1GE ok 00:58:38
1/1 EPA-10X10GE ok 00:58:25
R0 ASR1000-RP3 ok, active 01:01:00
R1 ASR1000-RP3 ok, standby 01:01:00
F0 ASR1000-ESP200 ok, active 01:01:00
F1 unknown 01:01:00
P0 ASR1000X-AC-1100W ok 01:00:01
P1 ASR1000X-AC-1100W ok 00:59:41
P2 ASR1000X-AC-1100W ok 00:59:57
P3 ASR1000X-AC-1100W ok 00:59:55
P4 Unknown N/A never
P5 Unknown N/A never
P6 ASR1000X-FAN ok 00:59:47
P7 ASR1000X-FAN ok 00:59:44
P8 ASR1000X-FAN ok 00:59:42
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
0 15072100 16.3(2r)
1 15072100 16.3(2r)
R0 17042115 17.3(1r)
R1 17042115 17.3(1r)
F0 13041200 17.3(1r)
F1 N/A N/A
How you can see SLOT 0 and Slot 1 they kept old version.
Do you have any ideas how to fix it ?
In the attached some log output.
Regards,
