Software upgrade of stack switch

[vrian_colaba]

Hello All,

Good Day! Can you help me how to upgrade the switch on this stack?

MCC01.IDF02.SWG01#show version | begin SW Version

Switch Ports Model              SW Version            SW Image

------ ----- -----              ----------            ----------

*    1 52    WS-C3750G-48PS     12.2(55)SE10          C3750-IPBASEK9-M

     2 54    WS-C3750X-48P      12.2(55)SE10          C3750E-IPBASEK9-M

ThankYou.

vrian

[Leo Laohoo]

*    1 52    WS-C3750G-48PS     12.2(55)SE10          C3750-IPBASEK9-M

     2 54    WS-C3750X-48P        12.2(55)SE10          C3750E-IPBASEK9-M

The Release Notes will provide detailed instructions on how to upgrade a stack.  

[vrian_colaba]

im getting an error when I upgraded it.

archive download-sw /overwrite /allow-feature-upgrade /reload tftp://10.4.2.125/c3750-ipbasek9-tar.150-2.SE10.tar

archive download-sw /overwrite /allow-feature-upgrade /reload tftp://10.4.2.125/c3750e-ipbasek9-tar.150-2.SE10.tar

MCC01.IDF02.SWG01#$ tftp://10.4.2.125/c3750e-ipbasek9-tar.150-2.SE10.tar

Loading c3750e-ipbasek9-tar.150-2.SE10.tar from 10.4.2.125 (via Vlan201): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[OK - 25753600 bytes]

Error: The image in the archive which would be used to upgrade

Error: system number 1 does not support that system type.

[Leo Laohoo]

Loading c3750e-ipbasek9-tar.150-2.SE10.tar from 10.4.2.125 (via Vlan201):

The error message makes sense.  Switch stack member #1 is a "WS-C3750G-48PS" but the IOS being loaded into this model is for a 3750E/X.  

The command should be:  archive download-sw /destination 1 tftp://10.4.2.125/c3750-ipbasek9-tar.150-2.SE10.tar

For the 3750E/X, the command should be:  archive download-sw /destination 2  tftp://10.4.2.125/c3750e-ipbasek9-tar.150-2.SE10.tar

[vrian_colaba]

When I use this, is there will have a problem when I reload it?

Thank you.

vrian

[Leo Laohoo]

When I use this, is there will have a problem when I reload it?

I don't understand the question.  Please elaborate further.  

If the correct command doesn't get entered this means the correct IOS doesn't get loaded.  

[vrian_colaba]

When I use this command below, is there a problem that I will encounter when I reload the switch? Is the stack setup will have an issue?

The command should be:  archive download-sw /destination 1 tftp://10.4.2.125/c3750-ipbasek9-tar.150-2.SE10.tar

For the 3750E/X, the command should be:  archive download-sw /destination 2  tftp://10.4.2.125/c3750e-ipbasek9-tar.150-2.SE10.tar

[vrian_colaba]

What will be the best procedure in upgrading the stack switch one at a time? Without using the archive download-sw command? Like for example, I have 6 switches in a stack.

Thank You.

vrian