In Catalyst OS (CatOS), a default gateway must be defined on the Supervisor Engine. This default gateway is usually the IP address of an active interface on the router. The router may be internal, such as the MultiLayer Switch Feature Card (MSFC) or Route Switch Module (RSM) on the Catalyst 6500 or 6000 series, and the Route Switch Feature Card (RSFC) or RSM on the Catalyst 5500 and 5000 series, or external. The default gateway allows frames (which then become encapsulated as packets) to be sent to the router for routing between VLANs or to other subnets.
The Supervisor Engine sends IP packets destined for other IP subnets to the default gateway (typically a router interface in the same network or subnet as the switch IP address). The switch does not use the IP routing table to forward traffic from connected devices. The switch forwards only IP traffic generated by the switch itself (for example, Telnet, TFTP, and ping).
You can define up to three default IP gateways. Use the primary keyword to make a primary gateway. If you do not specify a primary default gateway, the first gateway configured is the primary gateway. If more than one gateway is designated as primary, the last primary gateway configured is the primary default gateway.
The switch sends all off-network IP traffic to the primary default gateway. If connectivity to the primary gateway is lost, the switch attempts to use the backup gateways in the order they were configured. The switch sends periodic ping messages to determine whether each default gateway is up or down. If connectivity to the primary gateway is restored, the switch resumes sending traffic to the primary.
To specify one or more default gateways, perform the following steps in privileged mode:
Configure a default IP gateway address for the switch, by issuing the set ip route default gateway [metric] [primary] command.
(Optional) Configure additional default gateways for the switch, by issuing the set ip route default gateway [metric] [primary] command.
Verify that the default gateways appear correctly in the IP routing table, by issuing the show ip route command.
To remove default gateway entries, perform one of these tasks in privileged mode:
Clear an individual default gateway entry by issuing the clear ip route default gateway command.
Clear all default gateways and static routes, by issuing the clear ip route all command.
This example shows how to configure three default gateways on the switch and how to verify the default gateway configuration:
Console> (enable) set ip route default 10.1.1.10 Route added. Console> (enable) set ip route default 10.1.1.20 Route added. Console> (enable) set ip route default 10.1.1.1 primary Route added. Console> (enable) Console> (enable) show ip route Fragmentation Redirect Unreachable ------------- -------- ----------- enabled enabled enabled The primary gateway: 10.1.1.1 Destination Gateway RouteMask Flags Use Interface --------------- --------------- ---------- ----- -------- --------- default 10.1.1.1 0x0 UG 6 sc0 default 10.1.1.20 0x0 G 0 sc0 default 10.1.1.10 0x0 G 0 sc0 10.0.0.0 10.1.1.100 0xff000000 U 75 sc0 default default 0xff000000 UH 0 sl0 Console> (enable)
To participate in this event, please use the button to ask your questions
This topic is a chance to discuss more about SD-WAN), it's foundations and inner mechanisms as well as its correct design a...
This topic is a chance to discuss more about SD-WAN), it's foundations and inner mechanisms as well as its correct design and implementation to achieve desired business outcomes. Software-Defined WAN (SD-WAN), is a popular technology and this event is aim...
Trying to create an EEM script to reset lab gear to a default configuration and/or new version. I want to format the flash then copy over a new IOS and set the boot statement. The script works through the formating of the flash then stops.
I am working with packet tracer to create a layer 3 etherchannel, but running into an issue. these are the commands I was using channel-group 1 mode on int po1no switchport in videos, I see this work, but when I enter the no switchpor...
Hello. I need help if the EEM doesn't work because of a switch platform or EEM configuration.I configured EEM on the switch as follows:Swtich # show run!process cpu threshold type total rising 90 interval 5 switch 1!event manager applet CPU_Monitorev...