How to transfer a file to a router via SNMP, CISCO-FLASH-MIB
The examples below show how to copy a file from a tftp server to the flash via snmp, similar to
Router#copy tftp flash
Via SNMP the same operation can be performed from different sources:
"snmp set/get" commands run from the Router. When running snmp manager function,
"snmpset" commands applied from a Network Management Station running a snmp utility, or
"snmp_setany" commands applied from TCL shell in the router.
"snmp set/get" commands run from the Router
Those commands are hidden, with the advantage to configure&monitor via snmp from the router itself, without having to involve any NetworkManagement Station.
Here the configuration steps you need to execute:
Enable "snmp-server manager" in the Router
Run following commands from the enable mode in the router:
Router#snmp set v2c 10.1.0.2 private oid 188.8.131.52.184.108.40.206.10.1.2.1.1.11.666 integer 6
Router#snmp set v2c 10.1.0.2 private oid 220.127.116.11.18.104.22.168.10.1.2.1.1.11.666 integer 5
Router#snmp set v2c 10.1.0.2 private oid 22.214.171.124.126.96.36.199.10.1.2.1.1.2.666 integer 2
Router#snmp set v2c 10.1.0.2 private oid 188.8.131.52.184.108.40.206.10.1.2.1.1.3.666 integer 1
Router#snmp set v2c 10.1.0.2 private oid 220.127.116.11.18.104.22.168.10.1.2.1.1.4.666 ip-address 10.1.0.99
Router#snmp set v2c 10.1.0.2 private oid 22.214.171.124.126.96.36.199.10.1.2.1.1.5.666 string test
Router#snmp set v2c 10.1.0.2 private oid 188.8.131.52.184.108.40.206.10.1.2.1.1.6.666 string test
Router#snmp set v2c 10.1.0.2 private oid 220.127.116.11.18.104.22.168.10.1.2.1.1.11.666 integer 1
Note: "private" is the rw community string 10.1.0.2 is the ip address of the router 10.1.0.99 is the tftp server test is the file we want to move from tftp server to flash22.214.171.124.126.96.36.199.10.1.2.1.1.5 and 188.8.131.52.184.108.40.206.10.1.2.1.1.6 correspond ciscoFlashCopySourceName and ciscoFlashCopyDestinationName respectivaly
Hi,I am trying to get my head around best route selection but I couldn't get my head around it.BGP routing table entry for 220.127.116.11:100:18.104.22.168/24, version 193064
BGP Bestpath: deterministic-med
Multipath: eBGP iBGP
763 4755 6453 2914 42 19281
Had an issue like this before and it was stack member related, but this time the only issue is a module light coming up as amber. It doesn't appear to be hardware related, but I'm not sure. License Information for 'WS-X45-SUP7L-E'License Level: ipbas...
from what i unerstood, svi port will be th default gateway to the host that connect to it my question is does it mean that in a L3 switch i would have a port with vlan 10 (for example) and there will not be another port on that switch with vlan 10 ?&...
We have a deployment we cant really figure out why we cant create the actual Fabric. Under Provision, we only have devices and services, not fabric. All software packages are installed (SD-access is "Ready"), but still no Fabric-tab. Any clues? We are run...