Tag: "catalyst_5000" - Cisco Community

Latest Tagged

Port status is errdisable due to BPDU guard - ( ‎06-22-2009 04:02 PM )

by on

0 Replies 233632 Views

0 Replies

233632 Views

Catalyst switches that run CatOS generate the %SYS-3-P2_ERROR: 1/Have run out of vbufs (internal buf... - ( ‎06-22-2009 04:04 PM )

by on

0 Replies 777 Views

0 Replies

777 Views

The %MGMT-4-OUTOFNVRAM: Out of NVRAM space: error error message is seen on Cisco Catalyst switches r... - ( ‎06-22-2009 04:04 PM )

by on

0 Replies 1046 Views

0 Replies

1046 Views

The Error Msg: mfree 2: m= [Hex] , m_type=0 PID = 0 Kernel an error message appears in the logs of a... - ( ‎06-22-2009 04:06 PM )

by on

0 Replies 954 Views

0 Replies

954 Views

How to enable and disable the Finger service or protocol in Cisco switches - ( ‎06-22-2009 04:07 PM )

by on Latest post on by

2 Replies 27684 Views

2 Replies

27684 Views

How to configure the Gigabit Ethernet fiber-optic interface to support duplex speed in Cisco Catalys... - ( ‎06-22-2009 04:11 PM )

by on

0 Replies 11162 Views

0 Replies

11162 Views

Recovering from ErrDisabled port due to misconfiguration - ( ‎06-22-2009 04:39 PM )

by on Latest post on by

2 Replies 250887 Views

2 Replies

250887 Views

Catalyst switch running CatOS getting the error message %SPANTREE-7-MSGAGEEXPIRY: Msg Age timer expi... - ( ‎06-22-2009 04:41 PM )

by on

0 Replies 2031 Views

0 Replies

2031 Views

The %SYS-3-PORT_ERR: Port mod_num/port_num swBusCRCErrorDrop messages are logged on a Catalyst 500... - ( ‎06-17-2009 10:21 PM )

by on

0 Replies 967 Views

0 Replies

967 Views

Supervisor Engine module does not come online due to continuous booting loop, invalid boot variable,... - ( ‎06-22-2009 04:45 PM )

by on

0 Replies 2054 Views

0 Replies

2054 Views

Top Tagged

How to reset the VLAN and VTP information back to factory defaults in Cisco Catalyst switches - ( ‎06-22-2009 06:09 PM )

by on

0 Replies 36665 Views

0 Replies

36665 Views

The "%SYS-5-SYS_TIMECHNG: System time has changed to due to summertime" error message is received in... - ( ‎06-22-2009 06:09 PM )

by on

0 Replies 1761 Views

0 Replies

1761 Views

How to disable STP on a per port basis in Cisco Catalyst switches - ( ‎06-22-2009 06:08 PM )

by on

0 Replies 161850 Views

0 Replies

161850 Views

Slow performance of LAN due to a high degree of multicast traffic or frequent disruption of multicas... - ( ‎06-22-2009 05:40 PM )

by on

0 Replies 16440 Views

0 Replies

16440 Views

Configure ISL trunking between Catalyst switches that run CatOS and Cisco IOS (native mode) - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 1623 Views

0 Replies

1623 Views

A SPAN destination port is shown as "not connected" and does not communicate with the rest of the ne... - ( ‎06-22-2009 05:35 PM )

by on

0 Replies 9401 Views

0 Replies

9401 Views

Fan LED on Catalyst 4000, 5000 or 6000 series modular chassis is not green due to a hardware problem - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 640 Views

0 Replies

640 Views

The "port is a non-802.1q port" error message is displayed on Cisco Catalyst switches that run CatOS - ( ‎06-22-2009 05:34 PM )

by on

0 Replies 1398 Views

0 Replies

1398 Views

How to configure a default gateway on the Catalyst 6500, 6000, 5500, or 5000 series running CatOS so... - ( ‎06-22-2009 03:38 PM )

by on

0 Replies 10341 Views

0 Replies

10341 Views

Card in a modular Catalyst 4000, 5000 or 6000 series chassis does not function properly or is not on... - ( ‎06-22-2009 05:33 PM )

by on

0 Replies 2791 Views

0 Replies

2791 Views

Top Taggers

User

Count